Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£137.39
The WAGO 787-1616/000-1000 is a single-phase 24 V DC switched-mode power supply from the WAGO EPSITRON CLASSIC POWER range, designed for dependable industrial automation and electrical control applications. This specific variant combines a regulated DC output with NEC Class 2 limited-power characteristics, making it suitable for compatible installations requiring a Class 2 power source.
Delivering 24 V DC at 3.8 A, the WAGO 787-1616/000-1000 provides 91.2 W of nominal output power. Its wide-range input accepts 85–264 V AC or 120–300 V DC, while the adjustable output voltage of 23–28.5 V DC provides flexibility for compatible industrial control equipment.
With 87% typical efficiency, passive power factor correction, low output ripple and integrated overload protection, this DIN rail power supply supports reliable operation in demanding electrical environments. A green DC OK LED and active 24 V DC / 20 mA status output enable local and remote power supply monitoring.
The WAGO 787-1616/000-1000 is specifically designed to provide regulated 24 V DC power with NEC Class 2 limited-power characteristics. Unlike the standard WAGO 787-1616, this variant has a nominal output current of 3.8 A and a current limitation designed to maintain its Class 2 classification.
The output current is limited to 3.8 A at nominal voltage and 3.2 A when the adjusted output exceeds 25 V DC. These limits are particularly important when selecting a power supply for installations where the output circuit must satisfy specified limited-power requirements.
The integrated DC OK monitoring system includes a green operating status LED and an active 24 V DC / 20 mA signalling output. This enables compatible PLCs and monitoring devices to detect the power supply's operating condition, supporting diagnostics and maintenance.
With CAGE CLAMP® spring-pressure terminals, a compact DIN rail enclosure, low residual ripple and natural convection cooling, the WAGO 787-1616/000-1000 provides a practical combination of electrical performance, installation convenience and limited-power functionality for industrial control systems.
| Voltage type (supply voltage) | AC/DC |
|---|---|
| 1st secondary output voltage | 23 – 28.5 V |
| Secondary voltage adjustable | Yes |
| Suitable for distribution board | Yes |
| Stabilized | Yes |
| Type of electric connection | Spring clamp connection |
| Width in number of modular spacings | 3 |
| Height | 90 mm |
| Nominal value output voltage 1 | 24 V |
| Output voltage stabilized | Yes |
| Rated supply voltage AC 50 Hz | 85 – 264 V |
| Rated supply voltage AC 60 Hz | 85 – 264 V |
| Nominal value output current 1 | 3.8 A |
| Max. output current 1 | 3.8 A |
| Width | 52 mm |
| Rated supply voltage DC | 120 – 300 V |
| Short-circuit-proof | Yes |
| Degree of protection (IP) | IP20 |
| Power output | 91.2 W |
| Depth | 119 mm |
| Suitable for rail mounting | Yes |
| Manufacturer | WAGO |
| Series | EPSITRON CLASSIC POWER |
| Part number | 787-1616/000-1000 |
| Product type | Industrial switched-mode power supply |
| Power supply technology | Primary switched-mode |
| Number of phases | 1 |
| Nominal input voltage | 100–240 V AC |
| AC input voltage range | 85–264 V AC |
| DC input voltage range | 120–300 V DC |
| Nominal mains frequency | 44–66 Hz AC |
| Input voltage derating | −2.5% per V below 95 V AC |
| Input current at 240 V AC | ≤ 0.95 A |
| Input current at 100 V AC | ≤ 1.73 A |
| Maximum inrush current | ≤ 30 A |
| Power factor correction | Passive PFC |
| Mains failure hold-up time | ≥ 80 ms at 230 V AC; greater than 15 ms at 100 V AC |
| Nominal output voltage | 24 V DC (SELV) |
| Adjustable output voltage | 23–28.5 V DC |
| Factory output voltage | 24 V DC |
| Nominal output current | 3.8 A at 24 V DC |
| Nominal output power | 91.2 W |
| Number of regulated outputs | 1 |
| Output voltage regulation deviation | ≤ 1% |
| Residual ripple | ≤ 20 mV peak-to-peak |
| Current limitation | 3.8 A; 3.2 A when output voltage exceeds 25 V DC |
| Overload behaviour | Constant current |
| Output classification | Limited Power Source (LPS), NEC Class 2 |
| Typical efficiency | 87% |
| Maximum power loss | 20 W at 100 V AC and approximately 91 W load |
| DC OK indication | Green LED |
| Signal output | Active DC OK |
| Signal output rating | 24 V DC / 20 mA |
| Internal fuse | T 4 A / 250 V AC |
| Recommended upstream circuit breaker | 10 A or 16 A, characteristic B or C |
| DC input protection | External DC fuse required |
| Primary-to-secondary isolation | 4.242 kV DC |
| Protection class | Class II |
| Protection rating | IP20 according to EN 60529 |
| Overvoltage category | II |
| Pollution degree | 2 |
| Short-circuit protection | Yes |
| Open-circuit protection | Yes |
| Secondary overvoltage protection | Internal protective circuit, ≤ 40 V DC under fault conditions |
| Parallel operation | Supported |
| Series operation | Supported |
| MTBF | Greater than 500,000 hours according to IEC 61709 |
| Connection technology | WAGO CAGE CLAMP® |
| Connector series | WAGO 721 Series |
| Conductor cross-section | 0.08–2.5 mm² |
| Conductor size | 28–12 AWG |
| Strip length | 8–9 mm |
| Operating temperature | −25 to +70 °C, subject to derating |
| Mounting | 35 mm DIN rail |
| Cooling | Natural convection |
| Dimensions (W × H × D) | 52 × 90 × 119 mm |
| GTIN/EAN | 4055143060462 |
The WAGO 787-1616/000-1000 is a single-phase industrial switched-mode power supply designed to provide regulated 24 V DC power for automation and control equipment requiring an NEC Class 2 limited-power source.
The power supply provides 24 V DC at 3.8 A, delivering 91.2 W of nominal output power. Its output voltage is adjustable between 23–28.5 V DC, subject to current limitation.
Yes. The WAGO 787-1616/000-1000 is specified as an NEC Class 2 limited-power supply. Its output current is limited to 3.8 A, reducing to 3.2 A when the output voltage exceeds 25 V DC.
The standard WAGO 787-1616 provides a nominal 24 V DC at 4 A, equivalent to 96 W. The 787-1616/000-1000 provides 24 V DC at 3.8 A, equivalent to 91.2 W, and incorporates NEC Class 2 limited-power output characteristics.
The unit accepts 85–264 V AC or 120–300 V DC, with a nominal AC input voltage of 100–240 V AC. Output derating applies below 95 V AC.
Yes. The output voltage can be adjusted from 23–28.5 V DC. When the output voltage exceeds 25 V DC, the maximum output current is limited to 3.2 A to maintain the specified limited-power characteristics.
Yes. The power supply includes a green DC OK LED and an active 24 V DC / 20 mA DC OK output, allowing compatible monitoring equipment to detect its operating status.
Yes. The unit includes short-circuit and open-circuit protection together with constant-current overload behaviour, helping protect the power supply during abnormal load conditions.
Yes. The manufacturer supports parallel and series operation, provided the installation follows the relevant technical requirements. The Class 2 status of any combined output circuit must be evaluated separately.
The power supply is designed for 35 mm DIN rail mounting in a suitable electrical cabinet. It uses WAGO CAGE CLAMP® connections for conductors from 0.08–2.5 mm² and relies on natural convection cooling.
The WAGO 787-1616/000-1000 EPSITRON CLASSIC POWER supply combines 91.2 W of regulated 24 V DC output, NEC Class 2 limited-power characteristics, low output ripple, universal AC/DC input and active DC OK monitoring. It provides a dependable power supply solution for industrial automation engineers, electrical panel builders and equipment manufacturers working with compatible Class 2 control circuits.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.