Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£87.44
The WAGO 787-1017 is a compact, single-phase industrial switched-mode power supply designed to provide reliable, regulated 18 V DC power for compatible automation equipment, control electronics and electrical installations. Part of the WAGO EPSITRON COMPACT Power Series, this DIN rail-mounted power supply combines a wide input voltage range, adjustable DC output and space-saving stepped housing in a practical solution for industrial control cabinets and electrical distribution boards.
Designed for operation from a nominal 100–240 V AC single-phase supply, the WAGO 787-1017 accepts an AC input range of 85–264 V AC. It also supports a suitable DC input, subject to the manufacturer's voltage limits and external protection requirements. The output is factory-set to 18 V DC and can be adjusted between 15 and 28 V DC, making the unit suitable for applications requiring a configurable low-voltage DC supply.
At its nominal 18 V DC setting, the WAGO 787-1017 provides a rated output current of 2.4 A, equivalent to approximately 43 W of output power. At an adjusted output of 24 V DC, the manufacturer specifies an output current of 2 A under the applicable mounting conditions. The output current rating therefore depends on the selected voltage and installation arrangement, and the power supply should not be treated as a constant-current 2.5 A source throughout its entire adjustment range.
The WAGO 787-1017 features a stepped-profile enclosure suitable for installation in distribution boards and boxes, natural convection cooling and secure WAGO connection technology. Its electrically isolated output supports SELV and PELV applications when installed in accordance with the relevant standards. With a green operating status LED, overload protection and support for appropriately engineered parallel or series configurations, the unit offers a flexible power solution for industrial and electrical control applications.
The WAGO 787-1017 COMPACT power supply is particularly useful in applications requiring a regulated 18 V DC supply rather than the more common 24 V DC industrial control voltage. With a nominal current rating of 2.4 A at 18 V DC, it provides an appropriately sized power source for compatible low-voltage equipment without the installation space associated with larger industrial power supplies.
One of its most useful features is the adjustable 15–28 V DC output range. This allows the same power supply to serve a variety of compatible voltage requirements. However, engineers must consider the output current rating at the selected voltage: the manufacturer specifies 2.4 A at 18 V DC and 2 A at 24 V DC under the relevant mounting conditions. The maximum permissible current must be checked before selecting the power supply for a particular load.
The unit's wide 85–264 V AC input range supports operation from commonly used single-phase electrical supplies. It also offers DC input capability, making it suitable for appropriately engineered installations with a compatible upstream DC source. When the AC input is below 100 V AC, the manufacturer's derating requirements limit the available output current.
Its stepped-profile enclosure is designed for distribution boards and boxes, making the WAGO 787-1017 a practical choice for compact electrical installations. The housing can be mounted on a standard 35 mm DIN rail, allowing integration alongside other compatible control and distribution components. This makes it suitable for panel builders, OEM machinery manufacturers and maintenance engineers working with space-constrained enclosures.
The power supply uses natural convection cooling when horizontally mounted, avoiding the maintenance requirements associated with an integrated cooling fan. Overhead mounting is possible with derating, although the installation orientation, permissible output current and required ventilation clearances must be verified against the current WAGO instructions.
For dependable operation, the WAGO 787-1017 incorporates constant-current overload behaviour, a typical current limit of approximately 1.1 times rated current and an internal input fuse. A green status LED provides visual confirmation of operation. The output is electrically isolated, supporting appropriate SELV and PELV applications when the installation meets the relevant electrical safety requirements.
The unit also supports parallel and series operation in suitable configurations. These arrangements must be designed in accordance with the manufacturer's guidance, including any requirements for current sharing, output voltage adjustment and external protection. Overall, the WAGO 787-1017 offers a versatile combination of adjustable output voltage, compact dimensions and industrial switched-mode power supply functionality.
| Voltage type (supply voltage) | AC/DC |
|---|---|
| 1st secondary output voltage | 15 – 28 V |
| Secondary voltage adjustable | Yes |
| Suitable for distribution board | Yes |
| Stabilized | Yes |
| Type of electric connection | Spring clamp connection |
| Width in number of modular spacings | 4 |
| Height | 89 mm |
| Nominal value output voltage 1 | 18 V |
| Output voltage stabilized | Yes |
| Rated supply voltage AC 50 Hz | 85 – 264 V |
| Rated supply voltage AC 60 Hz | 85 – 264 V |
| Nominal value output current 1 | 2.4 A |
| Max. output current 1 | 2.4 A |
| Width | 72 mm |
| Rated supply voltage DC | 120 – 300 V |
| Short-circuit-proof | Yes |
| Degree of protection (IP) | IP20 |
| Power output | 43 W |
| Depth | 89 mm |
| Suitable for rail mounting | Yes |
| Manufacturer | WAGO |
| Product series | EPSITRON COMPACT Power |
| Manufacturer part number | 787-1017 |
| Product designation | Switched-mode power supply; Compact; single-phase; 18 V DC output |
| Product type | Industrial AC/DC switched-mode power supply |
| Power conversion technology | Primary switched-mode |
| Number of input phases | 1 |
| Nominal AC input voltage | 100–240 V AC |
| AC input voltage range | 85–264 V AC |
| DC input voltage range | 120–300 V DC in the more recent WAGO catalogue specification |
| Input voltage derating | Output current limited to 2 A below 100 V AC |
| Nominal mains frequency | 44–66 Hz |
| DC input frequency | 0 Hz |
| Input current at 230 V AC | ≤ 0.5 A |
| Input current at 110 V AC | ≤ 0.9 A |
| Discharge current | ≤ 1 mA |
| Inrush current | ≤ 30 A |
| Inrush current limitation | NTC |
| Power factor correction | Passive |
| Mains failure hold-up time at 230 V AC | ≥ 10 ms |
| Mains failure hold-up time at 110 V AC | ≥ 10 ms |
| Nominal output voltage | 18 V DC |
| Factory output voltage setting | 18 V DC |
| Adjustable output voltage | 15–28 V DC |
| Nominal output current at 18 V DC | 2.4 A |
| Nominal output current at 24 V DC | 2 A under specified mounting conditions |
| Nominal output power | 43 W |
| Number of regulated outputs | 1 |
| Output voltage adjustment accuracy | ≤ 2% |
| Residual output ripple | ≤ 100 mV peak-to-peak |
| Typical current limitation | 1.1 × nominal output current |
| Overload behaviour | Constant current |
| Operating status indication | Green LED |
| Internal input fuse | T 2 A / 250 V AC |
| DC input protection | External DC fuse required |
| Recommended external AC protection | 6 A characteristic C or 10 A characteristic B circuit breaker, subject to installation requirements |
| Typical efficiency | Approximately 84%, according to an earlier manufacturer datasheet |
| Power loss at 230 V AC, no load | 2.6 W in the referenced earlier datasheet |
| Power loss at 230 V AC, nominal load | 8.1 W in the referenced earlier datasheet |
| Maximum specified power loss | 8.2 W under the stated earlier datasheet conditions |
| Output isolation | Electrically isolated |
| Output safety classification | SELV; PELV in appropriate installations |
| Parallel operation | Supported |
| Series operation | Supported |
| Cooling method | Natural convection |
| Housing profile | Stepped profile for distribution boards and boxes |
| Mounting type | DIN-35 rail |
| Alternative mounting orientation | Overhead mounting permitted with derating |
| Housing width | 72 mm |
| Housing depth | Approximately 89 mm |
| Housing profile height | Approximately 55 mm |
| Dimensions | Approximately 72 × 55 × 89 mm, using the manufacturer's compact housing convention |
| GTIN / EAN | 4050821595731 |
| Country of origin | Germany |
| Packaging unit | 1 piece |
The WAGO 787-1017 is a single-phase switched-mode industrial power supply that converts a suitable AC or DC input into regulated low-voltage DC power. It is factory-set to 18 V DC and provides a rated output current of 2.4 A at 18 V DC, making it suitable for compatible industrial control equipment, electronics and electrical distribution applications.
Yes. The WAGO 787-1017 has an adjustable output range of 15–28 V DC, so it can be set to 24 V DC for compatible equipment. At 24 V DC, the manufacturer specifies a rated output current of 2 A under the applicable mounting conditions. The permissible output current must be checked for the selected voltage and installation arrangement.
The WAGO 787-1017 is designed for a nominal 100–240 V AC single-phase supply and supports an AC input range of 85–264 V AC. The more recent WAGO catalogue specification also lists a 120–300 V DC input range. An external DC fuse is required for DC-fed operation, and output current derating applies below 100 V AC.
Yes. The WAGO 787-1017 is designed for 35 mm DIN rail mounting and has a compact stepped-profile enclosure suitable for distribution boards and electrical boxes. It uses natural convection cooling when horizontally mounted. Overhead mounting is also possible with derating, subject to the manufacturer's installation requirements.
Yes. WAGO specifies that the 787-1017 supports parallel and series operation in appropriately designed configurations. Engineers must follow the manufacturer's instructions concerning output voltage settings, load sharing, electrical protection and permissible operating conditions before connecting multiple power supplies together.
The WAGO EPSITRON COMPACT Power Series provides practical switched-mode power conversion for industrial automation, electrical distribution and control applications. The WAGO 787-1017 combines an 18 V DC nominal output, adjustable 15–28 V DC regulation, wide single-phase input compatibility, an electrically isolated output and compact DIN rail mounting, making it a versatile solution for compatible low-voltage industrial equipment.
Technical references: WAGO 787-1017 official product page and WAGO power supplies catalogue and technical specifications. WAGO product headings identify this model as a 2.5 A unit, while detailed technical tables specify 2.4 A at 18 V DC. Some older documentation also differs from newer catalogues on the DC input voltage range. Confirm the applicable revision and current ratings before installation.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.