Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£1.15
The WAGO 231-566/001-000 is a robust 6-pole angled male PCB header designed for dependable, detachable electrical connections in industrial electronics, automation equipment and printed circuit board assemblies. Part of the WAGO MCS MIDI Classic 231 Series, this connector provides a reliable interface between printed circuit boards and compatible pluggable female connectors.
Featuring a 5.08 mm contact pitch, 90° angled mating orientation and 1.2 × 1.2 mm square solder pins, the 231-566/001-000 is designed for conventional through-hole technology (THT) PCB mounting. Its orange polyamide housing, shrouded contact interface, coding fingers and anti-rotation protection support secure installation and reliable connector alignment.
With an IEC rated current of 16 A, rated voltages of up to 630 V under specified insulation coordination conditions and a temperature range of −60 to +100 °C, this male header is suitable for industrial control electronics, modular automation systems and PCB-based power and signal connections. Its right-angle design enables convenient side-entry wiring in compact electronic equipment.
The WAGO MCS MIDI Classic connector system provides dependable, detachable electrical connections between printed circuit boards and external wiring assemblies. The WAGO 231-566/001-000 uses robust square through-hole solder pins to establish permanent electrical connections to PCB conductors, while its shrouded male mating interface enables compatible female connectors to be attached or removed during equipment assembly and maintenance.
Its 90° angled construction enables mating parallel to the PCB surface, making it suitable for electronic equipment requiring side-entry wiring or reduced vertical clearance. Tin-plated electrolytic copper contacts, a durable PA66 housing, integrated coding fingers and anti-rotation protection support reliable electrical performance and consistent mechanical integration.
The connector is intended for electrical connections without breaking capacity. Mating and unmating must be performed only when de-energised, and equipment designers must ensure that accessible male contacts cannot become hazardous when the mating connector is removed. Correct PCB layout, soldering procedures and compatible mating components are essential for dependable long-term operation.
Tick the specs you need, then view products that match.
| Current | 16 A | |
|---|---|---|
| Voltage | 320 V | |
| Product Series | WAGO 231 | |
| Rated surge voltage | 4 kV | |
| Number of plug-in contact rows | 1 | |
| Flammability class of insulation material according to UL 94 | V0 | |
| Operating temperature | -60 – 100 °C | |
| Rated current In | 16 A | |
| Material insulation body | Thermoplastic | |
| Housing colour | Orange | |
| Modular spacing contacts | 5.08 mm | |
| Angle PCB/contact | 0°/180° (horizontal) | |
| Contact type | Pin | |
| Type of electric connection | Soldering connection | |
| Type of fastening | Solder | |
| Type of connection | Flexible PCB-connector | |
| Length pin | 3.8 mm | |
| Modular spacing connections | 5.08 mm | |
| Number of poles | 6 | |
| Connector model | Free connector | |
| Suitable for PCB thickness | 1.5 mm | |
| Type of banding | None | |
| Rated voltage | 320 V | |
| Material of contact surface | Tin | |
| Pollution degree | 2 | |
| Overvoltage category | III | |
| Type of PCB fastening | Connecting contact | |
| Manufacturer | WAGO | |
| Series | MCS MIDI Classic, 231 Series | |
| Model | 231-566/001-000 | |
| Product type | Angled male PCB header | |
| Connector technology | Through-hole technology (THT) | |
| Number of potentials | 6 | |
| Number of rows | 1 | |
| Number of levels | 1 | |
| Pin spacing | 5.08 mm | |
| Connector orientation | Angled / right-angle | |
| Mating direction relative to PCB | 0° (parallel) | |
| Mounting type | PCB through-hole mounting | |
| Termination type | Solder pins | |
| Solder pin cross-section | 1.2 × 1.2 mm | |
| Solder pin length | 3.8 mm | |
| Solder pin arrangement | In-line | |
| Rated current (IEC) | 16 A | |
| Rated voltage (IEC, III/2) | 320 V | |
| Rated voltage (IEC, II/2) | 630 V | |
| Rated impulse voltage | 4 kV | |
| Rated current (UL) | 15 A | |
| Rated voltage (UL) | 600 V | |
| Temperature range | −60 to +100 °C | |
| Contact material | Electrolytic copper | |
| Contact plating | Tin | |
| Insulating material | Polyamide 66 (PA66) | |
| Flammability rating | UL 94 V-0 | |
| Contact gender | Male | |
| Housing configuration | Shrouded | |
| Coding fingers | Yes | |
| Anti-rotation protection | Yes | |
| Width | 33.68 mm | |
| Height above PCB surface | 8.4 mm | |
| Depth | 12 mm | |
| Weight | Approximately 2.458 g | |
| Packaging quantity | 100 pieces | |
| Applicable standards | IEC/EN 61984, UL 1059, UL 1977 | |
| Environmental compliance | RoHS compliant |
The WAGO 231-566/001-000 is a 6-pole angled male PCB header used to provide detachable electrical connections between printed circuit boards and compatible female connectors in industrial electronics, automation equipment and control systems.
The connector features 6 poles arranged in a single row with a 5.08 mm contact pitch, providing six separate electrical connection potentials through one PCB-mounted header.
The connector has an IEC rated current of 16 A and rated voltages of 320 V or 630 V, depending on the applicable overvoltage category and pollution degree. Its rated impulse voltage is 4 kV.
The connector uses through-hole solder mounting with 1.2 × 1.2 mm square solder pins and a 3.8 mm solder pin length. The pins are inserted into suitable PCB holes and soldered to establish secure mechanical and electrical connections.
The 231-566/001-000 is a 6-pole angled male PCB header with mating parallel to the circuit board, while the 231-366/001-000 is a 6-pole straight male PCB header with mating perpendicular to the board. Both use 5.08 mm contact spacing and 1.2 × 1.2 mm solder pins.
The header is designed for use with compatible 6-pole female connectors from the WAGO MCS MIDI Classic system featuring matching 5.08 mm contact pitch and mating geometry. Connector coding and electrical ratings should be checked before installation.
No. The WAGO MCS MIDI Classic connector system includes connectors without breaking capacity. The connector must be mated and unmated only when de-energised, and accessible male contacts must not remain live when the mating connector is removed.
WAGO MCS MIDI Classic PCB connectors provide industrial equipment manufacturers, electronics engineers and automation specialists with dependable electrical connectivity, robust through-hole mounting and flexible modular wiring interfaces for modern industrial control and electronic systems.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.