Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£2.75
The WAGO 231-546/001-000 is a robust 16-pole angled male PCB header designed for secure, detachable electrical connections in industrial electronics, automation equipment and printed circuit board assemblies. As part of the WAGO MCS MIDI Classic 231 Series, this connector provides a reliable interface between printed circuit boards and compatible pluggable female connectors.
Featuring a 5.08 mm pin spacing, 90° angled mating orientation and 1.0 × 1.0 mm square solder pins, the 231-546/001-000 is designed for conventional through-hole technology (THT) PCB mounting. Its orange polyamide housing and integrated coding fingers support convenient connector identification, controlled mating arrangements and dependable electrical integration.
With 16 electrical poles, an IEC rated current of 12 A and rated voltages of up to 630 V under specified insulation coordination conditions, this male header is suitable for industrial control electronics, modular automation systems and PCB-based power and signal interfaces. Its right-angle construction enables practical side-entry connections where available space or equipment layout requires mating parallel to the circuit board.
The WAGO MCS MIDI Classic connector system provides dependable, detachable electrical connections between printed circuit boards and external wiring assemblies. The WAGO 231-546/001-000 uses square through-hole solder pins to establish permanent electrical connections to PCB conductors, while its male mating interface allows compatible female connectors to be attached or removed during equipment assembly and maintenance.
The connector's 90° angled construction enables mating parallel to the PCB surface, making it particularly suitable for electronic equipment requiring side-entry wiring or reduced vertical clearance. Its tin-plated electrolytic copper contacts, durable PA66 insulating housing and coding fingers support consistent electrical performance and practical connector integration in industrial environments.
As part of the WAGO MCS system, this connector is classified as a connection without breaking capacity under IEC/EN 61984. It must not be connected or disconnected while live or under load. Equipment designers must also ensure that accessible male contacts cannot become live when the mating connector is removed.
Tick the specs you need, then view products that match.
| Current | 12 A | |
|---|---|---|
| Voltage | 320 V | |
| Product Series | WAGO 231 | |
| Rated surge voltage | 4 kV | |
| Number of plug-in contact rows | 1 | |
| Flammability class of insulation material according to UL 94 | V0 | |
| Operating temperature | -60 – 100 °C | |
| Rated current In | 12 A | |
| Material insulation body | Thermoplastic | |
| Housing colour | Orange | |
| Modular spacing contacts | 5.08 mm | |
| Angle PCB/contact | 0°/180° (horizontal) | |
| Contact type | Pin | |
| Type of electric connection | Soldering connection | |
| Type of fastening | Solder | |
| Type of connection | Flexible PCB-connector | |
| Length pin | 3.8 mm | |
| Modular spacing connections | 5.08 mm | |
| Number of poles | 16 | |
| Connector model | Free connector | |
| Suitable for PCB thickness | 1.5 mm | |
| Type of banding | None | |
| Rated voltage | 320 V | |
| Material of contact surface | Tin | |
| Pollution degree | 2 | |
| Overvoltage category | III | |
| Type of PCB fastening | Connecting contact | |
| Manufacturer | WAGO | |
| Series | MCS MIDI Classic, 231 Series | |
| Model | 231-546/001-000 | |
| Product type | Angled male PCB header | |
| Connector technology | Through-hole technology (THT) | |
| Number of potentials | 16 | |
| Number of connection types | 1 | |
| Number of levels | 1 | |
| Pin spacing | 5.08 mm | |
| Connector orientation | Angled / right-angle | |
| Mating direction relative to PCB | 0° (parallel) | |
| Mounting type | PCB through-hole mounting | |
| Termination type | Solder pins | |
| Solder pin cross-section | 1.0 × 1.0 mm | |
| Solder pin length | 3.8 mm | |
| Drilled hole diameter | 1.4 mm (+0.1 mm tolerance) | |
| Solder pin arrangement | In-line | |
| Rated current (IEC) | 12 A | |
| Rated voltage (IEC, III/3) | 320 V | |
| Rated voltage (IEC, III/2) | 320 V | |
| Rated voltage (IEC, II/2) | 630 V | |
| Rated impulse voltage | 4 kV | |
| Rated current (UL 1059, use groups B/D) | 10 A | |
| Rated voltage (UL 1059, use groups B/D) | 300 V | |
| Rated current (UL 1977, factory wiring) | 10 A | |
| Rated voltage (UL 1977, factory wiring) | 600 V | |
| Rated current (CSA, use groups B/D) | 10 A | |
| Rated voltage (CSA, use groups B/D) | 300 V | |
| Contact material | Electrolytic copper | |
| Contact plating | Tin | |
| Insulating material | Polyamide 66 (PA66) | |
| Flammability rating | UL 94 V-0 | |
| Contact gender | Male | |
| Connector configuration | Angled PCB male header | |
| Coding | Coding fingers | |
| Mismating protection | No built-in mismating protection | |
| Plug-in connection locking | Without locking mechanism | |
| Width | 84.4 mm | |
| Height | 12.2 mm | |
| Height above PCB surface | 8.4 mm | |
| Depth | 12 mm | |
| Weight | Approximately 5.3 g | |
| Packaging type | Box | |
| Standard packaging quantity | 50 pieces | |
| Country of origin | Germany | |
| GTIN | 4044918867436 | |
| Applicable standards | IEC/EN 61984, UL 1059, UL 1977 |
The WAGO 231-546/001-000 is a 16-pole angled male PCB header used to create detachable electrical connections between printed circuit boards and compatible female connectors in industrial electronics, automation equipment and control systems.
The connector features 16 poles with a 5.08 mm contact pitch, providing sixteen separate electrical connection potentials through one PCB-mounted header.
The connector has an IEC rated current of 12 A and rated voltages of 320 V or 630 V, depending on the applicable overvoltage category and pollution degree. Its rated impulse voltage is 4 kV.
The connector uses through-hole solder mounting with 1.0 × 1.0 mm square solder pins and a 3.8 mm solder pin length. The specified drilled PCB hole diameter is 1.4 mm with a +0.1 mm tolerance.
The WAGO 231-546/001-000 features an angled mating interface that allows a compatible female connector to be inserted parallel to the PCB surface. A straight PCB header has a mating direction perpendicular to the board, making the angled version useful for side-entry wiring and compact equipment layouts.
The connector is designed for use with compatible 16-pole female connectors from the WAGO MCS MIDI Classic system featuring matching 5.08 mm pitch and mating geometry. The complete connector configuration and coding arrangement should be checked before installation.
No. The WAGO MCS MIDI Classic connector system includes connectors without breaking capacity. The connector must not be mated or unmated while live or under load, and accessible male contacts must not remain live when disconnected.
WAGO MCS MIDI Classic PCB connectors provide industrial equipment manufacturers, electronics engineers and automation specialists with dependable electrical connectivity, secure through-hole mounting and practical modular wiring interfaces for modern industrial control and electronic systems.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.