Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£0.5015
The WAGO 231-533/001-000 is a 3-pole angled male PCB header from the WAGO MCS MIDI Classic Series 231. Designed for industrial pluggable wire-to-board connections, this component features a 5.08 mm contact pitch, 1.0 × 1.0 mm square solder pins and a distinctive orange insulating housing.
Its through-hole technology (THT) mounting system provides a soldered connection to the printed circuit board, while the shrouded male mating interface accepts an appropriately matched female connector. The angled contact arrangement is suitable for electronic equipment where external wiring must connect to a PCB through a compact, detachable interface.
With an IEC rated current of 12 A, specified IEC voltage ratings up to 630 V under applicable installation conditions and a durable polyamide housing, the WAGO 231-533/001-000 is a practical choice for industrial control electronics, modular equipment and OEM PCB assemblies.
The WAGO 231-533/001-000 features three contacts at 5.08 mm spacing, giving a distance of 10.16 mm between the first and last contact centres.
The manufacturer's published dimensional relationships for the connector family include:
For the three-pole configuration, these relationships produce the following nominal reference dimensions:
The product's published physical dimensions include a width of 18.36 mm, a height of 12.2 mm and a depth of 12 mm. The solder pins are 3.8 mm long, with a specified PCB drilled-hole diameter of 1.4 mm (+0.1 mm).
Always refer to the manufacturer's dimensional drawing when preparing the PCB footprint. The labelled L, L1 and L2 dimensions should not be used interchangeably as overall enclosure clearance measurements.
The WAGO 231-533/001-000 creates a permanent soldered electrical connection to a printed circuit board while allowing a compatible female connector to be plugged into and removed from the male header.
Each of its three electrical positions uses a 1.0 × 1.0 mm square solder pin. These pins are inserted through appropriately prepared PCB holes and soldered using a suitable manufacturing process. The resulting joint provides both the electrical connection and part of the component's mechanical retention.
The connector uses a 5.08 mm pitch, which is an important distinction from the 5 mm pitch used by some other WAGO Series 231 headers. Even a small difference in nominal spacing can prevent correct mating or produce mechanical stress, so matching the exact pitch is essential.
The four-sided shrouded housing surrounds the male contacts, helping guide the female mating connector. Its orange PA66 insulation provides separation between electrical positions, while the tin-plated copper contacts provide the conductive interface.
Variable coding allows suitable coding arrangements to be implemented within the compatible connector system. This can help distinguish different circuits when several similar connectors are installed in the same equipment. However, the product's datasheet identifies mismating protection as absent, so the designer must not assume that the standard header prevents every incorrect connection.
The WAGO 231-533/001-000 is a male PCB header, not a direct wire-entry terminal block. External conductors are terminated using a separately selected compatible female connector, which may incorporate WAGO spring-pressure conductor connection technology.
Electrical safety: Do not mate or disconnect the connector under load unless the complete connector system is specifically approved for that operation. Ensure that exposed male contacts cannot remain hazardous when the mating connector is removed.
The WAGO 231-533/001-000 is specifically a 3-pole, 5.08 mm-pitch, orange THT male header with 1.0 × 1.0 mm solder pins.
It should not be confused with WAGO 231-333/001-000, which is a different three-pole header configuration. When replacing an existing connector, verify the full part number, mounting arrangement, pitch and mating interface.
It also differs from the 231-533/001-000/105-604 variant, which is a black THR header intended for suitable through-hole reflow soldering processes. The standard 231-533/001-000 is the orange THT version.
When selecting a female connector, confirm the three-pole configuration, 5.08 mm pitch, mating geometry, coding arrangement and electrical ratings. Pole count and pitch alone do not guarantee compatibility.
Tick the specs you need, then view products that match.
| Current | 12 A | |
|---|---|---|
| Voltage | 320 V | |
| Product Series | WAGO 231 | |
| Rated surge voltage | 4 kV | |
| Number of plug-in contact rows | 1 | |
| Flammability class of insulation material according to UL 94 | V0 | |
| Operating temperature | -60 – 100 °C | |
| Rated current In | 12 A | |
| Material insulation body | Thermoplastic | |
| Housing colour | Orange | |
| Modular spacing contacts | 5.08 mm | |
| Angle PCB/contact | 0°/180° (horizontal) | |
| Contact type | Pin | |
| Type of electric connection | Soldering connection | |
| Type of fastening | Solder | |
| Type of connection | Flexible PCB-connector | |
| Length pin | 3.8 mm | |
| Modular spacing connections | 5.08 mm | |
| Number of poles | 3 | |
| Connector model | Free connector | |
| Suitable for PCB thickness | 1.5 mm | |
| Type of banding | None | |
| Rated voltage | 320 V | |
| Material of contact surface | Tin | |
| Pollution degree | 2 | |
| Overvoltage category | III | |
| Type of PCB fastening | Connecting contact | |
| Manufacturer | WAGO | |
| Manufacturer part number | 231-533/001-000 | |
| Product family | MCS MIDI Classic | |
| Series | 231 | |
| Product type | Angled THT male PCB header | |
| Connector gender | Male | |
| Number of potentials | 3 | |
| Number of levels | 1 | |
| Contact pitch | 5.08 mm / 0.2 in | |
| PCB termination | Through-hole soldering | |
| Solder-pin arrangement | In-line | |
| Solder pins per potential | 1 | |
| Solder-pin dimensions | 1.0 × 1.0 mm | |
| Solder-pin length | 3.8 mm | |
| PCB drilled-hole diameter | 1.4 mm (+0.1 mm) | |
| Rated current (IEC) | 12 A | |
| Rated voltage (IEC III/3) | 320 V | |
| Rated voltage (IEC III/2) | 320 V | |
| Rated voltage (IEC II/2) | 630 V | |
| Rated impulse withstand voltage | 4 kV | |
| Rated current (UL 1059, Use Groups B and D) | 10 A | |
| Rated voltage (UL 1059, Use Groups B and D) | 300 V | |
| Rated current (UL 1977) | 10 A | |
| Rated voltage (UL 1977) | 600 V | |
| Width | 18.36 mm | |
| Height | 12.2 mm | |
| Height above PCB surface | 8.4 mm | |
| Depth | 12 mm | |
| Contact material | Electrolytic copper | |
| Contact plating | Tin | |
| Housing material | Polyamide 66 (PA66) | |
| Flammability classification | UL94 V-0 | |
| Variable coding | Yes | |
| Anti-rotation protection | Yes | |
| Integrated locking mechanism | No | |
| Material temperature limits | −60 to +100 °C | |
| Approximate weight | 1 g | |
| Country of origin | Poland | |
| GTIN / EAN | 4044918866804 |
The WAGO 231-533/001-000 is a 3-pole angled THT male PCB header from the MCS MIDI Classic Series 231. It features 5.08 mm contact spacing, 1.0 × 1.0 mm solder pins and an orange insulating housing.
The connector has 3 poles, providing three independent electrical connection positions in a single-level arrangement.
The WAGO 231-533/001-000 has a nominal contact pitch of 5.08 mm, equivalent to 0.2 inches.
Yes. WAGO identifies the 231-533/001-000 as an angled THT male header. Refer to the official dimensional drawing to confirm the required board layout and mating clearances.
The manufacturer's IEC datasheet specifies a 12 A rated current. UL 1059 and UL 1977 ratings specify 10 A under their respective approval conditions.
The IEC ratings are 320 V for category III, pollution degrees 3 and 2, and 630 V for category II, pollution degree 2. UL voltage ratings depend on the applicable approval standard and use group.
The connector uses 1.0 × 1.0 mm square solder pins with a length of 3.8 mm. The manufacturer's specified drilled-hole diameter is 1.4 mm (+0.1 mm).
It uses through-hole technology (THT). The solder pins are inserted through prepared PCB holes and soldered to the printed circuit board.
The standard WAGO 231-533/001-000 features an orange polyamide 66 insulating housing.
No. The male header itself uses solder-pin termination. A compatible female connector may use WAGO CAGE CLAMP® spring-pressure technology for connecting external conductors.
Both are three-pole male PCB headers, but they belong to different dimensional and mounting configurations. The 231-533/001-000 uses 5.08 mm pitch. Confirm the complete PCB footprint and mating geometry before considering a substitution.
The standard 231-533/001-000 is an orange THT male header. The 231-533/001-000/105-604 is a black THR version intended for suitable through-hole reflow assembly processes.
Do not connect or disconnect the header under load unless the complete connector system is specifically approved for load-breaking operation. Follow appropriate electrical isolation procedures.
Choose a compatible 3-pole female connector with 5.08 mm pitch and the correct mating geometry, coding and electrical ratings. Verify the exact mating part number using WAGO documentation.
The WAGO 231-533/001-000 combines three electrical positions, 5.08 mm contact spacing, 1.0 × 1.0 mm solder pins and a 12 A IEC current rating in an orange, shrouded male PCB header. Its through-hole termination and detachable mating interface make it a practical component for compatible industrial wire-to-board connection systems.
Official manufacturer reference: WAGO 231-533/001-000 Product Information
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.