Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£1.52
The WAGO 231-468/001-000 is an 8-pole right-angle male PCB header from the WAGO MCS MIDI Classic 231 Series. Designed for industrial wire-to-board connections, it combines 5 mm contact spacing, 1.2 × 1.2 mm square solder pins and a 16 A IEC rated current in a compact, grey, shrouded connector housing.
Its 90° angled design allows a compatible female connector to mate parallel to the printed circuit board, making it particularly suitable for PCB edge connections, industrial control modules and electronic equipment with restricted vertical clearance.
Featuring through-hole technology (THT), tin-plated electrolytic copper contacts and a polyamide insulating housing, the WAGO 231-468/001-000 provides a practical, detachable electrical interface for professional industrial PCB assemblies.
The WAGO 231-468/001-000 is designed to create a dependable interface between a printed circuit board and a compatible detachable female connector. Its eight square solder pins are inserted into correctly dimensioned PCB holes and soldered to establish the electrical connection to the circuit board.
The 1.2 × 1.2 mm solder pins distinguish this connector from lower-current Series 231 headers that use smaller 1.0 × 1.0 mm pins. The larger contact cross-section is associated with the product's 16 A IEC rated current, subject to the applicable electrical installation conditions and the ratings of the complete mating assembly.
The right-angle configuration positions the mating interface parallel to the PCB. This makes the connector particularly useful where the wiring connection needs to be accessible from the side of an electronic assembly, rather than from above the board.
The 5 mm contact spacing supports a compact eight-position connection arrangement. However, 5 mm and 5.08 mm connectors must not be assumed interchangeable. Both the pitch and the mechanical mating geometry must match the selected female connector.
The four-sided shrouded housing helps guide the mating connector and provides mechanical protection around the male contacts. Tin-plated electrolytic copper contacts provide a conductive mating surface, while the grey polyamide housing insulates the individual electrical positions.
As a male PCB header, the WAGO 231-468/001-000 does not accept stripped wires directly. External wiring is terminated in an appropriately matched female pluggable connector, which may use WAGO spring-pressure conductor connection technology.
Installation safety: The connector must not be connected or disconnected under load unless the complete connector system is expressly approved for that operation. Equipment design should also ensure that accessible male contacts cannot remain hazardous when the mating connector is removed.
WAGO offers several Series 231 male PCB headers with different pole counts, contact pitches, solder-pin dimensions and mounting orientations. The 231-468/001-000 is specifically an 8-pole, 5 mm-pitch, right-angle THT header with 1.2 × 1.2 mm solder pins.
It should not be confused with the WAGO 231-438/001-000, which is also an 8-pole angled header but uses 1.0 × 1.0 mm solder pins and has a lower IEC rated current.
It should also not be confused with the 231-468/001-000/105-604 variant, which is a black THR header designed for a different PCB assembly process. The standard 231-468/001-000 is the grey THT version.
Always confirm the exact manufacturer part number, mating connector, PCB footprint and electrical requirements before installation.
Tick the specs you need, then view products that match.
| Current | 16 A | |
|---|---|---|
| Voltage | 320 V | |
| Product Series | WAGO 231 | |
| Rated surge voltage | 4 kV | |
| Number of plug-in contact rows | 1 | |
| Flammability class of insulation material according to UL 94 | V0 | |
| Operating temperature | -60 – 100 °C | |
| Rated current In | 16 A | |
| Material insulation body | Thermoplastic | |
| Housing colour | Grey | |
| Modular spacing contacts | 5 mm | |
| Angle PCB/contact | 0°/180° (horizontal) | |
| Contact type | Pin | |
| Type of electric connection | Soldering connection | |
| Type of fastening | Solder | |
| Type of connection | Flexible PCB-connector | |
| Length pin | 3.8 mm | |
| Modular spacing connections | 5 mm | |
| Number of poles | 8 | |
| Connector model | Free connector | |
| Suitable for PCB thickness | 1.5 mm | |
| Type of banding | None | |
| Rated voltage | 320 V | |
| Material of contact surface | Tin | |
| Pollution degree | 2 | |
| Overvoltage category | III | |
| Type of PCB fastening | Connecting contact | |
| Manufacturer | WAGO | |
| Manufacturer part number | 231-468/001-000 | |
| Product series | MCS MIDI Classic 231 | |
| Product type | Angled THT male PCB header | |
| Connector gender | Male | |
| Number of electrical positions | 8 | |
| Number of rows | 1 | |
| Number of levels | 1 | |
| Contact pitch | 5 mm / 0.197 in | |
| Connector orientation | 90° right-angle | |
| Mating direction | Parallel to PCB surface | |
| PCB mounting method | Through-hole technology (THT) | |
| Termination method | Soldering | |
| Solder-pin dimensions | 1.2 × 1.2 mm | |
| Rated current (IEC) | 16 A | |
| Rated voltage (IEC, III/3) | 250 V | |
| Rated voltage (IEC, III/2) | 320 V | |
| Rated voltage (IEC, II/2) | 630 V | |
| Rated impulse voltage | 4 kV | |
| Contact material | Electrolytic copper | |
| Contact plating | Tin | |
| Housing material | Polyamide | |
| Housing design | Shrouded | |
| Flammability classification | UL94 V-0 | |
| Minimum material temperature | −60 °C | |
| Maximum material temperature | +100 °C | |
| Width | 43.2 mm | |
| Depth | 12 mm | |
| Height | Approximately 12.2 mm | |
| Anti-rotation protection | Yes | |
| RoHS compliance | Yes | |
| Country of origin | Germany | |
| GTIN / EAN | 4044918930499 | |
| Standard packaging unit | 100 pieces |
The WAGO 231-468/001-000 is an 8-pole angled male PCB header from the MCS MIDI Classic 231 Series, featuring 5 mm contact spacing, through-hole solder termination and a grey insulating housing.
The connector has 8 poles, providing eight independent electrical connection positions in a single row.
The WAGO 231-468/001-000 has a nominal contact pitch of 5 mm. It should not be confused with connectors using 5.08 mm spacing.
It is an angled, right-angle PCB header. The mating connector approaches parallel to the PCB surface.
The connector has an IEC rated current of 16 A. The permissible operating current also depends on the mating connector, conductor arrangement, PCB design and installation conditions.
The IEC voltage ratings are 250 V for overvoltage category III, pollution degree 3; 320 V for category III, pollution degree 2; and 630 V for category II, pollution degree 2.
The WAGO 231-468/001-000 uses 1.2 × 1.2 mm square solder pins. The PCB hole pattern and drill dimensions should be confirmed against the manufacturer's dimensional drawing.
It uses through-hole technology (THT). Its solder pins are inserted through the printed circuit board and soldered to the PCB.
The standard WAGO 231-468/001-000 has a grey polyamide insulating housing.
No. The male header itself uses solder-pin PCB termination. A compatible female connector may use WAGO CAGE CLAMP® spring-pressure technology for external conductors.
Both are 8-pole angled PCB headers with 5 mm contact spacing. The 231-468/001-000 uses 1.2 × 1.2 mm solder pins and is rated at 16 A IEC, while the 231-438/001-000 uses 1.0 × 1.0 mm solder pins and is rated at 12 A IEC.
The standard 231-468/001-000 is a grey THT male PCB header. The 231-468/001-000/105-604 is a black THR version intended for suitable through-hole reflow assembly processes. Their PCB assembly requirements must be checked separately.
Do not connect or disconnect the header under load unless the complete connector system is specifically approved for load-breaking operation. Follow appropriate electrical isolation procedures.
The WAGO 231-468/001-000 requires a compatible 8-pole female connector with 5 mm pitch and the correct mating geometry. Confirm the exact female connector part number and electrical ratings using WAGO documentation.
The WAGO 231-468/001-000 combines an 8-pole configuration, 5 mm contact spacing, 1.2 × 1.2 mm solder pins and a 16 A IEC current rating in a compact right-angle male PCB header. Its shrouded mating interface and grey insulating housing make it a practical component for compatible industrial wire-to-board connection systems.
Manufacturer reference: WAGO 231-468/001-000 Product Information
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.