Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£0.782
The WAGO 231-234/001-000 is a 4-pole, straight male PCB header from the WAGO MCS MIDI Classic 231 Series. Designed for industrial electronic equipment and modular electrical connections, this through-hole technology (THT) connector features 7.5 mm pin spacing, 1.0 × 1.0 mm square solder pins and a grey insulating housing.
Unlike the female cable connectors in the WAGO 231 Series, the 231-234/001-000 is designed for direct soldering onto a printed circuit board. Its four male contacts provide a detachable electrical interface when paired with a compatible female pluggable connector. The straight solder pins support vertical PCB mounting, while the shrouded connector housing helps guide the mating component.
With a 12 A IEC rated current, IEC rated voltages of up to 1,000 V under the specified insulation coordination conditions and a −60 to +100 °C temperature range, the WAGO 231-234/001-000 is suitable for appropriately rated industrial control and electronic applications. Its tin-plated copper contacts, coding fingers and through-hole mounting arrangement make it a practical solution for PCB-based electrical interfaces.
The WAGO MCS MIDI Classic connector system provides modular electrical interfaces for industrial control equipment, machine building and electronic assemblies. The 231-234/001-000 is designed specifically for PCB installation, using straight through-hole solder pins to create a permanent connection to the circuit board while allowing a compatible female connector to be plugged in and removed for servicing or equipment assembly.
Its 7.5 mm pin spacing, 12 A IEC rated current and tin-plated contacts make it suitable for appropriately rated industrial control, signalling and power circuits. The selected female connector must match the four-pole configuration, contact spacing and applicable electrical ratings. Because the MCS connector system does not provide breaking capacity under IEC/EN 61984, connectors must not be connected or disconnected while energised or under load. Circuit design should also prevent exposed male pins from remaining live when unmated.
Tick the specs you need, then view products that match.
| Current | 12 A | |
|---|---|---|
| Voltage | 630 V | |
| Product Series | WAGO 231 | |
| Rated surge voltage | 6 kV | |
| Number of plug-in contact rows | 1 | |
| Flammability class of insulation material according to UL 94 | V0 | |
| Operating temperature | -60 – 100 °C | |
| Rated current In | 12 A | |
| Material insulation body | Thermoplastic | |
| Housing colour | Grey | |
| Modular spacing contacts | 7.5 mm | |
| Angle PCB/contact | 90° (upwards vertical) | |
| Contact type | Pin | |
| Type of electric connection | Soldering connection | |
| Type of fastening | Solder | |
| Type of connection | Flexible PCB-connector | |
| Length pin | 5 mm | |
| Modular spacing connections | 7.5 mm | |
| Number of poles | 4 | |
| Connector model | Free connector | |
| Suitable for PCB thickness | 1.5 mm | |
| Type of banding | None | |
| Rated voltage | 630 V | |
| Material of contact surface | Tin | |
| Pollution degree | 2 | |
| Overvoltage category | III | |
| Type of PCB fastening | Connecting contact | |
| Manufacturer | WAGO | |
| Series | MCS MIDI Classic / 231 Series | |
| Manufacturer part number | 231-234/001-000 | |
| Product type | THT male PCB header | |
| Connector gender | Male | |
| Total number of potentials | 4 | |
| Number of levels | 1 | |
| Number of solder pins per potential | 1 | |
| Pin spacing | 7.5 mm | |
| PCB connection technology | Through-hole technology (THT) | |
| Termination method | Soldering | |
| Solder-pin orientation | Straight | |
| PCB mounting orientation | Vertical | |
| Mating direction relative to PCB | 90° | |
| Solder-pin dimensions | 1.0 × 1.0 mm | |
| Solder-pin length | 5 mm | |
| Recommended drilled-hole diameter | 1.4 mm (+0.1 mm tolerance) | |
| Solder-pin arrangement | In-line across the male header | |
| Rated current (IEC) | 12 A | |
| Rated voltage (III / 3) | 500 V | |
| Rated voltage (III / 2) | 630 V | |
| Rated voltage (II / 2) | 1,000 V | |
| Rated impulse voltage | 6 kV | |
| Rated voltage (UL 1977) | 600 V | |
| Rated current (UL 1977) | 10 A | |
| Width | 30.7 mm | |
| Height | 17 mm | |
| Height above PCB surface | 12 mm | |
| Depth | 8.4 mm | |
| Contact material | Electrolytic copper | |
| Contact plating | Tin | |
| Insulating housing material | Polyamide 66 (PA66) | |
| Flammability classification | UL 94 V-0 | |
| Weight | Approximately 1.7 g | |
| Variable coding | Yes | |
| Anti-rotation protection | Yes | |
| Mismating protection | No | |
| Plug-in connection locking | None | |
| GTIN | 4044918864572 | |
| Applicable connector standards | IEC/EN 61984, UL 1059 and UL 1977 | |
| Manufacturer product reference | WAGO 231-234/001-000 Official Product Page |
The WAGO 231-234/001-000 is a four-pole male PCB header designed to provide a detachable electrical connection between a printed circuit board and a compatible female connector in industrial automation and electronic equipment.
It is a male PCB header with four contact positions and straight solder pins. It is soldered onto a printed circuit board and mates with an appropriately compatible female pluggable connector.
The connector uses 1.0 × 1.0 mm square solder pins with a length of 5 mm. It is intended for vertical through-hole PCB mounting, with a specified drilled-hole diameter of 1.4 mm and a positive tolerance of 0.1 mm.
The connector has a 12 A IEC rated current and IEC rated voltages of 500 V for category III/3, 630 V for category III/2 and 1,000 V for category II/2. Its rated impulse voltage is 6 kV, while its UL 1977 ratings are 600 V and 10 A.
No. The WAGO 231-234/001-000 is a through-hole soldered male PCB header and does not directly terminate conductors using CAGE CLAMP technology. CAGE CLAMP conductor termination may be provided by a compatible female connector used with the header.
WAGO MCS MIDI Classic PCB headers provide a practical connection interface between printed circuit boards and detachable wiring assemblies. The 231-234/001-000 combines four male contacts, straight through-hole solder pins, 7.5 mm spacing and a shrouded insulating housing to support reliable PCB integration, modular equipment assembly and straightforward maintenance.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.