Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£2.92
The WAGO 231-2103/037-000/133-000 is a specialised variant of the WAGO MCS MIDI Classic 231 Series female pluggable connector family. The corresponding base configuration, 231-2103/037-000, is a 3-pole, 2-conductor female connector featuring Push-in CAGE CLAMP® spring connection technology, 5 mm contact spacing and lateral locking levers. It is designed for modular electrical connections in industrial automation, machine control and electronic equipment.
The connector's distinctive two-conductor-per-pole arrangement allows two conductors to connect to each electrical potential, providing six conductor connection points across three poles. This configuration is particularly useful for loop-through wiring, where power or signal circuits need to continue through an assembly. The electrical bus connection can remain intact even when the female connector is separated from its mating header.
The base connector is rated at 16 A under IEC conditions and accepts conductors up to 2.5 mm². Its spring-pressure connection technology eliminates the need for screw tightening, while the lateral locking levers help secure the mated connection against unintended separation.
Variant identification: The full part number 231-2103/037-000/133-000 is listed by industrial distributors as a WAGO 2-conductor female connector. The additional /133-000 suffix identifies a specific product variant, but its precise technical significance has not been independently established. The specifications below describe the documented 231-2103/037-000 base configuration; any variant-specific differences should be confirmed against WAGO's documentation before procurement or installation.
The following electrical, connection and dimensional specifications are documented for the WAGO 231-2103/037-000 base connector. They should be treated as reference information for the 231-2103/037-000/133-000 variant until the full-suffix specification is confirmed.
The WAGO 231-2103 connector family uses Push-in CAGE CLAMP® spring-pressure connection technology to provide dependable conductor termination. Unlike conventional screw-terminal connectors, the spring connection maintains contact pressure without requiring periodic screw retightening.
Suitable solid conductors and fine-stranded conductors fitted with appropriate ferrules can be inserted directly into the connection points. For conductor types that require assistance, an appropriate operating tool is used to actuate the spring connection. This combination supports efficient wiring during manufacturing, installation and maintenance.
The connector's two-conductor-per-pole design is especially valuable for electrical distribution applications. Each of the three poles provides two conductor-entry positions connected to the same electrical potential. This enables an incoming conductor and an outgoing conductor to share a common connection point without additional external jumper wiring.
A significant advantage of this arrangement is that the loop-through connection remains electrically continuous when the female plug is unmated from its corresponding male header. In suitably designed systems, this allows a power or data bus to continue through the female connector while the connected electronic module is removed for maintenance or replacement.
The 5 mm contact pitch provides a compact connection interface for compatible WAGO MCS MIDI Classic components. Engineers should verify that the selected male header has the correct pole count, pitch, contact configuration and locking compatibility. A matching nominal pitch alone does not establish full mechanical compatibility.
The connector's lateral locking levers provide positive mechanical retention between the female plug and a compatible mating component. These locking features are useful in industrial machinery and equipment where vibration, movement or maintenance activity could otherwise place stress on the connection.
Integrated coding fingers allow compatible connector assemblies to be configured for identification and mating control. Correctly implemented coding can help reduce the likelihood of connecting a cable assembly to an unintended circuit, particularly where several similar connectors are installed close together.
For conductor preparation, the documented base connector requires a 9–10 mm stripping length. The conductor should be fully inserted into the spring connection, and the installer should verify secure retention according to the manufacturer's instructions. Ferrule size and conductor type must remain within the specified limits.
The base connector has an IEC rated current of 16 A, with voltage ratings determined by the relevant overvoltage category and pollution degree. These electrical ratings must be considered together with conductor size, ambient conditions, the mating header and the complete equipment design.
The connector should not be treated as a load-breaking device unless the complete system is specifically approved for that function. Before mating, unmating or changing wiring, the circuit should be safely isolated and verified as de-energised. The /133-000 variant suffix should also be checked against manufacturer documentation before applying base-model specifications to a final installation.
The WAGO 231-2103/037-000/133-000 is listed as a variant of a 3-pole, 2-conductor female pluggable connector from the WAGO MCS MIDI Classic 231 Series. The documented base configuration is designed for modular electrical connections, industrial control equipment and loop-through wiring applications. The specific characteristics of the /133-000 variant should be confirmed with WAGO.
The documented base connector has 3 electrical poles and 2 conductor connection points per pole, providing 6 conductor connection points in total. This arrangement allows two conductors to share each electrical potential and supports loop-through wiring.
The documented base connector accepts 0.2–2.5 mm² solid and fine-stranded conductors. Fine-stranded conductors with insulated ferrules are specified from 0.25–1.5 mm², while those with uninsulated ferrules are specified from 0.25–2.5 mm². The required conductor stripping length is 9–10 mm.
The documented base connector has an IEC rated current of 16 A. Its IEC voltage ratings are 320 V under category III/3 and III/2 conditions and 630 V under category II/2 conditions. The rated impulse voltage is 4 kV. These ratings should be verified for the full /133-000 variant before use.
The /133-000 suffix identifies a specific version of the WAGO 231-2103/037-000 connector. However, its precise technical significance has not been independently verified. The base connector is documented as a grey, 3-pole female connector with Push-in CAGE CLAMP® connections and lateral locking levers. Any changes introduced by the additional suffix should be confirmed using WAGO's full product documentation.
WAGO MCS MIDI Classic connectors support modular electrical connections in industrial automation, machinery and electronic equipment. The documented 231-2103 base configuration combines three electrical poles, six conductor connection points, Push-in CAGE CLAMP® technology and lateral locking levers to provide an efficient solution for loop-through wiring and detachable industrial connections. The precise specification of the 231-2103/037-000/133-000 variant should be confirmed before final selection.
Manufacturer reference: WAGO 231-2103/037-000 Base Product Information. The full 231-2103/037-000/133-000 suffix variant requires separate manufacturer confirmation.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.