Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
Finder 7P.23.9.500.1015 is a three-pole Type 2 photovoltaic surge protection device for compatible 1500 V DC solar PV installations. Featuring a 15 kA nominal discharge current, three replaceable varistor modules, visual protection status indication, SPDT remote signalling contact, IP20 protection and 35 mm DIN rail mounting. Suitable for photovoltaic combiner boxes, inverter DC protection and renewable energy distribution systems.
£130.41
The Finder 7P.23.9.500.1015 is a high-performance Type 2 photovoltaic surge protection device (SPD) designed to protect high-voltage solar PV installations against transient overvoltages caused by lightning activity and electrical switching disturbances. Part of the Finder 7P Series, this three-pole surge arrester combines metal oxide varistor technology, replaceable protective modules, visual status indication and remote signalling contacts in a compact DIN rail-mounted assembly.
Specifically developed for 1,500 V DC photovoltaic systems, the Finder 7P.23.9.500.1015 is suitable for appropriately designed commercial, industrial and utility-scale solar installations. Its maximum continuous operating voltage (UCPV) of 1,500 V DC allows it to be incorporated into compatible high-voltage PV protection arrangements, helping protect solar inverters, DC distribution equipment and associated electrical components.
The device provides a nominal discharge current (In) of 15 kA, measured using the standard 8/20 µs surge current waveform. Its three-varistor protective arrangement helps divert transient surge currents through the intended protective paths, reducing the voltage exposure of connected photovoltaic equipment when the SPD is correctly installed and coordinated.
A key advantage of the Finder 7P.23.9.500.1015 is its integrated remote status signalling. In addition to local visual indication of the varistor condition, the device incorporates an auxiliary changeover contact that can be connected to compatible monitoring systems. This allows maintenance personnel to receive information about SPD status without relying exclusively on physical inspection of the electrical enclosure.
With replaceable varistor cartridges, 35 mm DIN rail mounting and a compact three-module housing, this Finder surge protector is designed for professional photovoltaic installations where protection performance, maintainability and remote monitoring are important considerations.
Photovoltaic installations are particularly vulnerable to transient overvoltages because solar arrays are often mounted on rooftops, exposed structures or open ground. Lightning activity near a PV installation can induce voltage surges in long DC cable runs, potentially affecting inverters, monitoring equipment and other electrical components.
The Finder 7P.23.9.500.1015 is designed to help reduce these risks by providing Type 2 surge protection for compatible high-voltage photovoltaic DC circuits. Its metal oxide varistor elements respond to transient overvoltages by changing their electrical resistance and providing a controlled discharge path for surge current.
Under normal operating conditions, the varistors present high resistance. During a suitable transient event, their resistance decreases rapidly, allowing surge energy to be diverted through the intended protective paths. This voltage-limiting action helps reduce the transient stress experienced by connected electrical equipment.
The 1,500 V DC UCPV rating is especially important in larger photovoltaic systems where DC string voltages may be considerably higher than those found in smaller residential installations. Correct selection must account for the maximum possible PV array voltage, including the effect of low ambient temperatures on solar module open-circuit voltage.
With a 15 kA nominal discharge current, measured using the 8/20 µs waveform, the device provides a defined surge current capability for Type 2 protection applications. Its suitability must be assessed as part of the complete installation, including earthing, cable routing, upstream protection and coordination with other SPDs.
The three-pole construction is specifically intended for photovoltaic DC surge protection. It should not be confused with a conventional three-phase AC surge protection device, despite the similar number of protective poles.
A distinguishing feature of the Finder 7P.23.9.500.1015 is its remote signalling contact, which provides an additional method of monitoring the condition of the surge protection device.
In many photovoltaic installations, DC protection equipment is located inside combiner boxes, distribution cabinets or electrical enclosures that are not continuously attended. Without remote indication, a failed protective module may remain unnoticed until the next scheduled inspection.
The integrated SPDT changeover contact can be connected to compatible monitoring equipment to provide information about the SPD's protective status. Depending on the system design, this information may be incorporated into a building management system, industrial monitoring system or photovoltaic installation alarm circuit.
The remote contact is intended for status signalling, not for switching the main photovoltaic power circuit. The electrical ratings and wiring arrangement of the auxiliary contact must be checked against Finder's installation documentation before connection.
The device also includes visual varistor status indication, allowing maintenance personnel to inspect the protective elements directly during routine electrical inspections.
This combination of local and remote indication makes the Finder 7P.23.9.500.1015 particularly useful in commercial and industrial solar installations where rapid identification of a protection fault can support more effective maintenance planning.
The Finder 7P.23.9.500.1015 is designed for mounting on a standard 35 mm DIN rail according to EN 60715. Its approximately 53.8 mm width occupies around three modular positions, allowing installation within compatible photovoltaic DC distribution enclosures.
The SPD must be connected according to Finder's specified photovoltaic wiring arrangement. Correct selection and installation are essential because high-voltage DC circuits have different electrical characteristics from conventional AC systems.
Surge protection conductors should be kept as short and direct as practicable to minimise additional voltage drop during transient events. The installation should also incorporate suitable earthing and any required protective devices, in accordance with the manufacturer's instructions and applicable electrical standards.
The replaceable varistor modules simplify maintenance by allowing the protective elements to be replaced when required. The correct replacement cartridges must be selected for the installed SPD assembly.
Routine maintenance should include checking the visual status indicators, verifying the remote signalling function where connected and inspecting the surrounding electrical enclosure for signs of damage or deterioration.
Photovoltaic DC circuits can remain energised whenever sufficient light reaches the solar modules. Installation, inspection and replacement must therefore be carried out by a competent electrical professional using suitable DC isolation and safe working procedures.
| Manufacturer | Finder |
|---|---|
| Series | 7P Series |
| Manufacturer part number | 7P.23.9.500.1015 |
| Alternative part number | 7P2395001015 |
| EAN / GTIN | 8012823413327 |
| Product type | Photovoltaic surge protection device |
| SPD classification | Type 2 / Class II |
| Application | High-voltage photovoltaic DC systems |
| Number of poles | 3 |
| Protection technology | Metal oxide varistor |
| Number of protective varistor elements | 3 |
| Maximum continuous operating voltage (UCPV) | 1,500 V DC |
| Nominal discharge current (In) | 15 kA |
| Nominal discharge current waveform | 8/20 µs |
| Remote signalling | Yes |
| Auxiliary contact configuration | SPDT / changeover contact |
| Visual protection status indication | Yes |
| Replaceable protective modules | Yes |
| Mounting method | DIN rail |
| DIN rail standard | EN 60715 |
| DIN rail size | 35 mm |
| Overall height | 89.6 mm |
| Overall width | 53.8 mm |
| Overall depth | 65.9 mm |
| Approximate modular width | 3 DIN modules |
| Maximum conductor size | 25 mm² |
| Ingress protection | IP20 |
| Operating temperature range | -40 °C to +80 °C |
| Net weight | Approximately 378.2 g |
| Country of origin | Czechia |
| Recommended installation location | Suitable photovoltaic electrical enclosure or DC distribution cabinet |
| Typical lightning protection zone boundary | LPZ 1 to LPZ 2 |
The Finder 7P.23.9.500.1015 is a Type 2 photovoltaic surge protection device designed to help protect compatible high-voltage DC solar installations against transient overvoltages caused by lightning activity and electrical switching disturbances.
Yes. The device has a maximum continuous operating voltage (UCPV) of 1,500 V DC and is designed for appropriately rated photovoltaic installations. The maximum possible PV array voltage must be checked before selecting the SPD.
It is a Type 2 SPD, intended primarily for protection against induced lightning surges and switching transients. Installations requiring protection against partial direct lightning currents may need additional Type 1 protection.
The device has a nominal discharge current (In) of 15 kA, measured using the standard 8/20 µs surge current waveform.
Yes. The Finder 7P.23.9.500.1015 includes an SPDT remote signalling contact that can be connected to compatible monitoring equipment to indicate the status of the surge protection device.
The 7P.23.9.500.1015 includes remote status signalling as well as visual indication. The corresponding 7P.23.9.500.0015 is the version without remote signalling. Both are intended for compatible 1,500 V DC photovoltaic Type 2 surge protection applications.
Yes. The device incorporates replaceable varistor protection modules, allowing the protective elements to be serviced when required while retaining the compatible installed assembly.
No. Although the device has a three-pole construction, it is designed for photovoltaic DC applications, not as a general-purpose three-phase AC mains surge protector.
The device mounts onto a standard 35 mm DIN rail and has an approximate width of 53.8 mm. It must be installed within a suitable electrical enclosure by a competent professional following Finder's instructions.
The device has an IP20 protection rating and is not suitable for unprotected outdoor exposure. Outdoor photovoltaic installations require an appropriately rated enclosure.
The device is specified for an operating temperature range of -40 °C to +80 °C, subject to correct installation and the conditions of the complete electrical assembly.
The Finder 7P Series provides specialist surge protection solutions for photovoltaic and electrical distribution installations. Combining a 1,500 V DC rating, Type 2 protection, 15 kA nominal discharge current, three-varistor construction, replaceable modules and integrated remote status signalling, the Finder 7P.23.9.500.1015 is a practical choice for protecting and monitoring compatible high-voltage solar PV electrical systems.
Manufacturer documentation: Finder 7P Series Surge Protection Devices Technical Catalogue.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.