Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
ABB EPX-2504-E2-MCCB (1TVS151800S3614) 250 A four-pole XT4 electronic LSI incoming MCCB with long-time, short-time and instantaneous overcurrent protection for compatible ABB Protecta Power distribution panelboards.
£2,154.58
The ABB EPX-2504-E2-MCCB is a 250 A four-pole electronic LSI moulded case circuit breaker (MCCB) designed for compatible ABB Protecta Power low-voltage electrical distribution panelboards. Based on the ABB SACE Tmax XT4 circuit breaker platform, this incoming protective device combines manual switching with electronic overload and short-circuit protection for appropriately designed three-phase electrical installations.
Part of the ABB Protecta Power Enclosures range, the EPX-2504-E2-MCCB incorporates electronic LSI protection, providing long-time (L), short-time (S) and instantaneous (I) overcurrent protection functions. These functions support the development of coordinated protection settings, allowing electrical designers to consider overload protection, delayed short-circuit tripping and instantaneous fault clearance within the same incoming circuit breaker.
Its four-pole (4P) configuration makes the EPX-2504-E2-MCCB suitable for approved three-phase distribution arrangements requiring a fourth pole. With a 250 A current rating, XT4 device frame and manufacturer order code 1TVS151800S3614, this genuine ABB product provides a dedicated incoming electronic protection option for compatible Protecta Power panelboard assemblies.
Incoming circuit protection plays an important role in the safety and performance of low-voltage electrical distribution systems. The incoming MCCB provides a protective switching point between the electrical supply and the distribution assembly, helping protect the connected circuits against overload and short-circuit conditions when correctly selected, installed and coordinated with the wider electrical network.
The ABB EPX-2504-E2-MCCB uses the ABB SACE Tmax XT4 platform with electronic LSI protection technology. Unlike a conventional thermal-magnetic MCCB, an electronic LSI circuit breaker provides distinct long-time, short-time and instantaneous overcurrent protection functions. This enables the electrical designer to consider the response of the incoming device under different fault conditions and configure the protection characteristics within the limits of the installed trip unit.
The long-time (L) function provides overload protection for sustained overcurrent conditions. Its purpose is to help protect conductors and distribution equipment against excessive heating caused by currents above the selected protection threshold. The appropriate long-time setting must be determined from the electrical load, conductor rating and manufacturer's trip-unit documentation.
The short-time (S) function provides short-circuit protection with an intentional time-delay characteristic. This function can be useful in installations where protection coordination between incoming and outgoing circuit breakers is required. By considering the operating characteristics of multiple protective devices, engineers can seek to limit the extent of supply interruption during certain downstream faults.
The instantaneous (I) function provides rapid tripping in response to sufficiently high short-circuit currents. The combination of L, S and I functions gives the EPX-2504-E2-MCCB a versatile electronic protection arrangement, although the presence of LSI functionality does not automatically guarantee discrimination or selectivity. The completed protection design must be verified using the applicable ABB coordination data and calculated fault levels.
The four-pole configuration distinguishes the EPX-2504-E2-MCCB from three-pole incoming circuit breakers. Four-pole devices are used in suitable three-phase distribution arrangements where the electrical design requires an additional pole, commonly associated with the neutral conductor. The correct treatment of the neutral, including switching and any applicable protection requirements, must be verified against the specific earthing system and manufacturer's device configuration.
The EPX-2504-E2-MCCB is intended for integration into a compatible ABB Protecta Power panelboard. ABB's modular approach allows incoming circuit breakers, connection kits, enclosures and outgoing protective devices to be specified as coordinated components. The associated EPX-2504CK is the four-pole XT4 incoming connection kit for the corresponding arrangement and should be specified separately where required by the approved panelboard design.
ABB Protecta Power selection information identifies a 150 mm² maximum incoming cable capacity for XT4 devices. This is a published connection capacity for the relevant arrangement rather than a universal allowance for all conductor types. Actual suitability depends on the terminals installed, cable construction, connection method and manufacturer's installation instructions.
The EPX-2504-E2-MCCB is an incoming protective device rather than a complete enclosed distribution panelboard. Before installation, the designer must confirm the device's rated operational voltage, short-circuit breaking capacity, electronic trip settings, terminal configuration and compatibility with the intended assembly. The complete installation must comply with applicable electrical installation standards and low-voltage switchgear assembly requirements.
| Product group | Protecta Power Enclosures |
|---|---|
| Product range | Protecta Power |
| ABB order code | 1TVS151800S3614 |
| Manufacturer product description | 250A 4P Electronic LSI MCCB - XT4 |
| Product type | Moulded case circuit breaker (MCCB) |
| Device category | Electronic-trip incoming MCCB |
| Rated current | 250 A |
| Number of poles | 4P (four-pole) |
| Device frame | ABB SACE Tmax XT4 |
| Protection technology | Electronic trip |
| Protection functions | LSI |
| Long-time protection (L) | Overload protection |
| Short-time protection (S) | Short-circuit protection with time-delay functionality |
| Instantaneous protection (I) | Short-circuit protection without intentional time delay |
| Operating functionality | Manual switching and automatic overcurrent tripping |
| Intended installation position | Incoming supply section |
| Compatible distribution system | ABB Protecta Power |
| Designated current configuration | 250 A |
| Associated incoming connection kit | EPX-2504CK, subject to approved assembly configuration |
| Published XT4 maximum incoming cable capacity | 150 mm², subject to terminal and cable compatibility |
| System type | Low-voltage electrical power distribution |
| Application | Commercial and industrial three-phase incoming circuit protection |
| Product classification | 250 A four-pole electronic LSI incoming MCCB |
The ABB EPX-2504-E2-MCCB is a 250 A four-pole electronic LSI moulded case circuit breaker designed for compatible ABB Protecta Power electrical distribution panelboards. It provides incoming overload and short-circuit protection using the ABB Tmax XT4 device platform.
LSI refers to three electronic overcurrent protection functions: long-time (L) overload protection, short-time (S) short-circuit protection and instantaneous (I) short-circuit protection. The available adjustment ranges and settings must be confirmed against the supplied ABB electronic trip unit documentation.
The EPX-2504-E2-MCCB has a 250 A current rating and a four-pole (4P) configuration. It uses the ABB SACE Tmax XT4 circuit breaker platform and is intended for compatible Protecta Power incoming distribution arrangements.
The EPX-2504-E2-MCCB uses electronic LSI protection with long-time, short-time and instantaneous functions. A thermal-magnetic XT4 MCCB uses thermal and magnetic tripping elements. The electronic LSI arrangement offers additional protection coordination flexibility, subject to the specific trip-unit capabilities and installation design.
The EPX-2504-E2-MCCB is identified as an incoming MCCB device, not a complete panelboard or connection assembly. The associated EPX-2504CK is the ABB 250 A four-pole XT4 incoming connection kit and should be specified separately where required by the approved Protecta Power panelboard configuration.
ABB Protecta Power provides coordinated low-voltage electrical distribution solutions for professional commercial and industrial installations. The EPX-2504-E2-MCCB combines a 250 A four-pole Tmax XT4 circuit breaker platform with electronic LSI overcurrent protection, giving electrical designers, contractors and panel builders a dedicated incoming protective device for compatible Protecta Power distribution assemblies.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.