Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
ABB EPX-XT1N-TM0253 (1SDX253308R1) 25 A three-pole Tmax XT1N thermal-magnetic outgoing MCCB with a 36 kA breaking-capacity classification for compatible ABB Protecta Power electrical distribution panelboards.
£348.06
The ABB EPX-XT1N-TM0253 is a 25 A three-pole moulded case circuit breaker (MCCB) with a 36 kA breaking-capacity classification, designed for compatible ABB Protecta Power electrical distribution panelboards. Identified by manufacturer order code 1SDX253308R1, this protective device belongs to the Protecta Power Devices product group and provides a dedicated outgoing circuit protection solution for professional low-voltage electrical installations.
Based on the ABB SACE Tmax XT1N circuit breaker platform, the EPX-XT1N-TM0253 incorporates thermal-magnetic (TMA) protection to respond to overload and short-circuit conditions. Its 25 A rated current and three-pole (3P) configuration make it suitable for appropriately designed three-phase outgoing circuits requiring common switching and overcurrent protection of the three phase conductors.
The EPX-XT1N-TM0253 is listed in ABB's Protecta Power selection literature within the 25 A, three-pole, 36 kA thermal-magnetic outgoing MCCB range. The XT1 platform provides a compact circuit breaker arrangement, with a published 80 mm three-pole device width. This combination of protective characteristics, compact construction and clear ABB product identification makes the EPX-XT1N-TM0253 suitable for electrical contractors, consulting engineers and panel builders specifying compatible Protecta Power distribution equipment.
Outgoing circuit protection is an essential element of a professionally designed low-voltage distribution system. Each circuit breaker must be selected according to the connected load, conductor characteristics, installation conditions and prospective fault current. The ABB EPX-XT1N-TM0253 provides a 25 A three-pole MCCB solution for compatible Protecta Power assemblies, helping protect the connected circuit against overload and short-circuit conditions.
The product uses the ABB SACE Tmax XT1N circuit breaker platform. The XT1 designation identifies the circuit breaker frame family, while the N designation identifies the relevant device variant. The 25 A current rating specifies the rating of this particular outgoing protective device and must be considered when selecting conductors, connected equipment and protective coordination arrangements.
The thermal-magnetic protection arrangement combines two complementary overcurrent protection functions. The thermal element responds to sustained overload conditions that may cause excessive heating in electrical conductors and equipment. The magnetic element responds to sufficiently high short-circuit currents, providing rapid protective tripping when its operating threshold is reached. The precise operating characteristics and any available adjustment settings must be confirmed from ABB's technical documentation.
The three-pole configuration makes the EPX-XT1N-TM0253 suitable for appropriately designed three-phase circuits. The three protected poles operate together through the circuit breaker's common mechanism, enabling coordinated disconnection of the phase conductors. This arrangement is relevant where the electrical design requires common switching and protective operation across a three-phase outgoing supply.
The EPX-XT1N-TM0253 is specified as a 25 A, three-pole, 36 kA thermal-magnetic MCCB. The 36 kA classification is an important part of the product identification, but the electrical designer must verify the applicable breaking-capacity rating at the intended operational voltage. The manufacturer's detailed data should be consulted for the relevant ultimate short-circuit breaking capacity (Icu) and service short-circuit breaking capacity (Ics).
The 25 A rating distinguishes this model from other XT1N outgoing circuit breakers, including the 32 A EPX-XT1N-TM0323 and 63 A EPX-XT1N-TM0633. Although these devices share the XT1N platform, they are intended for circuits with different protection requirements. A higher-rated breaker should not be substituted without confirming that its protective characteristics remain suitable for the connected conductors and equipment.
ABB's Protecta Power selection literature identifies the XT1 three-pole device width as 80 mm. This provides a useful reference for panelboard layout and device selection. However, the published width should not be interpreted as the complete installed space requirement, as mounting accessories, terminal arrangements, cable routing and electrical clearances must also be considered.
The ABB Protecta Power system uses coordinated outgoing MCCB mounting arrangements to integrate circuit breakers into compatible distribution assemblies. The appropriate XT1 three-pole base plate, cover and associated installation components must be selected for the intended panelboard. These components should be checked against current ABB ordering information and installation instructions rather than assumed to be included with the circuit breaker.
For three-phase distribution circuits, the prospective short-circuit current at the installed position must be assessed alongside the circuit breaker's breaking-capacity rating. Where discrimination, selectivity or backup protection is required, the designer should refer to ABB's published coordination information. Protective devices from the same manufacturer do not automatically provide full selectivity under every fault condition.
Before installation, the electrical designer must verify the rated operational voltage, breaking capacity, thermal-magnetic trip characteristics, conductor termination requirements, mounting arrangement and panelboard compatibility. The completed distribution assembly must satisfy applicable electrical installation and low-voltage switchgear assembly requirements. Installation, inspection and commissioning should be carried out by competent electrical personnel using current ABB technical documentation.
| Product group | Protecta Power Devices |
|---|---|
| Compatible distribution range | ABB Protecta Power |
| ABB order code | 1SDX253308R1 |
| Manufacturer product description | 25A 3P 36kA MCCB - TMA |
| Product type | Moulded case circuit breaker (MCCB) |
| Device application | Outgoing circuit protection |
| Rated current | 25 A |
| Number of poles | 3P (three-pole) |
| Circuit breaker platform | ABB SACE Tmax XT1 |
| Device variant | XT1N |
| Frame family | XT1 |
| Protection technology | Thermal-magnetic |
| Trip designation | TMA |
| Overload protection | Thermal trip function |
| Short-circuit protection | Magnetic trip function |
| Published breaking-capacity classification | 36 kA |
| Breaking-capacity verification | Confirm the applicable rated operational voltage and detailed ABB Icu/Ics ratings |
| Published XT1 three-pole device width | 80 mm |
| Mounting arrangement | Compatible ABB Protecta Power outgoing MCCB assembly |
| Associated installation components | Appropriate XT1 three-pole mounting accessories and protective cover, as specified for the panelboard |
| Operating functionality | Manual switching and automatic overcurrent tripping |
| System type | Low-voltage electrical distribution |
| Intended installation position | Compatible outgoing distribution circuit |
| Typical circuit arrangement | Three-phase outgoing circuit |
The ABB EPX-XT1N-TM0253 is a 25 A three-pole thermal-magnetic MCCB designed for compatible ABB Protecta Power outgoing distribution circuits. It provides overload and short-circuit protection using the ABB SACE Tmax XT1N circuit breaker platform.
TMA identifies the device's thermal-magnetic protection arrangement. The thermal element responds to sustained overload conditions, while the magnetic element responds to short-circuit conditions. The exact trip characteristics and available adjustment settings must be confirmed from the relevant ABB technical documentation.
The EPX-XT1N-TM0253 has a 25 A current rating and a three-pole (3P) configuration. It belongs to the ABB SACE Tmax XT1N circuit breaker range and is intended for suitable three-phase outgoing circuit protection applications.
The EPX-XT1N-TM0253 is specified as a 36 kA MCCB. The applicable short-circuit breaking capacity must be verified at the intended operational voltage, including the relevant Icu and Ics ratings, before the device is selected for an installation.
The EPX-XT1N-TM0253 must be installed using the appropriate ABB Protecta Power outgoing MCCB mounting arrangement. The compatible XT1 three-pole base plate, protective cover and any associated installation components should be confirmed against the selected panelboard and current ABB documentation. These components should not be assumed to be included with the circuit breaker.
ABB Protecta Power provides coordinated low-voltage electrical distribution components for commercial and industrial installations. The EPX-XT1N-TM0253 combines a 25 A three-pole Tmax XT1N circuit breaker with thermal-magnetic protection and a 36 kA breaking-capacity classification, offering electrical contractors and panel builders a clearly identified outgoing protective device for compatible Protecta Power assemblies.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.