Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
ABB EPX-A1C-040L3 (1SDA123214R1) 40 A single-pole Formula A1N125 thermal-magnetic outgoing MCCB with LSC L3 connection arrangement and 25 kA published breaking-capacity classification for compatible ABB Protecta Power distribution panelboards.
£194.77
The ABB EPX-A1C-040L3 is a 40 A single-pole moulded case circuit breaker (MCCB) with an LSC L3 connection arrangement, designed for compatible ABB Protecta Power electrical distribution panelboards. Identified by ABB manufacturer order code 1SDA123214R1, this device belongs to the Protecta Power Devices product group and provides dedicated outgoing circuit protection for professional low-voltage electrical installations.
Based on the ABB Formula A1N125 circuit breaker platform, the EPX-A1C-040L3 uses thermal-magnetic (TMA) protection to respond to overload and short-circuit conditions. Its 40 A rated current and single-pole (1P) configuration make it suitable for appropriately designed outgoing circuits where a moulded case circuit breaker is required within a compatible Protecta Power assembly.
ABB's Protecta Power selection literature identifies the 40 A single-pole A1N125 outgoing MCCB with a 25 kA breaking-capacity classification. The product's L3 designation identifies the specified connection variant, distinguishing it from the corresponding L1 and L2 versions. Together, these characteristics provide a clearly identified outgoing protection solution for electrical contractors, consulting engineers and panel builders specifying ABB distribution equipment.
Outgoing circuit protection is an essential element of a professionally designed electrical distribution panelboard. Each protective device must be selected to suit the connected electrical load, conductor characteristics, installation conditions and prospective fault current. The ABB EPX-A1C-040L3 provides a 40 A single-pole MCCB solution for compatible Protecta Power assemblies, helping protect the outgoing circuit against overload and short-circuit conditions.
The device uses the ABB Formula A1N125 circuit breaker platform. The A1N125 designation identifies the circuit breaker family and its 125 A frame classification, while the 40 A rating identifies the current rating of this particular protective device. These values serve different purposes: the frame designation describes the breaker family, whereas the 40 A rating is relevant to the selection of the outgoing circuit protection.
The thermal-magnetic protection arrangement combines two complementary overcurrent protection functions. The thermal element responds to sustained overload conditions that can cause excessive heating in conductors and electrical equipment. The magnetic element responds to sufficiently high short-circuit currents, providing rapid tripping when the applicable operating threshold is reached.
ABB's Protecta Power selection literature identifies the 40 A single-pole A1N125 outgoing MCCB with a 25 kA breaking-capacity classification. This provides a useful reference when comparing outgoing protective devices within the ABB Protecta Power range. However, the applicable breaking capacity must always be checked at the installation's operational voltage and against the exact manufacturer's circuit breaker data before specification.
The LSC L3 designation is an important part of the EPX-A1C-040L3 product reference. ABB offers corresponding 40 A single-pole outgoing variants identified as EPX-A1C-040L1, EPX-A1C-040L2 and EPX-A1C-040L3. These variants allow the required connection arrangement to be specified for the intended outgoing position. They should not be treated as interchangeable without confirming the approved panelboard configuration.
The ABB Protecta Power outgoing MCCB system uses dedicated mounting and cover components to integrate protective devices into the finished electrical distribution assembly. ABB's selection literature specifies that an MCCB base plate and cover are required with each outgoing device. The EPX-A1C-040L3 should therefore be considered an outgoing protective device for use within a compatible assembly, rather than a complete enclosed distribution product.
ABB's published Protecta Power information identifies a maximum cable capacity of 50 mm² for A1 single-pole devices. This figure describes the connection capacity of the relevant device arrangement and is not a recommended conductor size for a 40 A circuit. The appropriate cable cross-section must be determined from the connected load, installation method, voltage drop, fault protection requirements and terminal compatibility.
When specifying the EPX-A1C-040L3, the electrical designer must verify the rated operational voltage, short-circuit breaking capacity, protective characteristics, conductor compatibility and panelboard installation requirements. The outgoing circuit breaker must also be coordinated with the upstream protection arrangement where necessary. Installation and commissioning should follow current ABB technical documentation and applicable electrical installation standards.
| Product group | Protecta Power Devices |
|---|---|
| Compatible distribution range | ABB Protecta Power |
| ABB order code | 1SDA123214R1 |
| Manufacturer product description | A1N125 40A 1p + LSC L3 TMA |
| Product type | Moulded case circuit breaker (MCCB) with LSC connection arrangement |
| Device application | Outgoing circuit protection |
| Rated current | 40 A |
| Number of poles | 1P (single-pole) |
| Circuit breaker family | ABB Formula A1N125 |
| Frame family | 125 A |
| Protection technology | Thermal-magnetic |
| Trip designation | TMA |
| Overload protection | Thermal trip function |
| Short-circuit protection | Magnetic trip function |
| Published breaking-capacity classification | 25 kA; verify the applicable operational voltage and detailed ABB ratings |
| Connection arrangement | LSC L3 |
| Connection variant | L3 |
| Alternative connection variants | EPX-A1C-040L1 and EPX-A1C-040L2 |
| Published A1 single-pole maximum cable capacity | 50 mm², subject to terminal and installation requirements |
| Associated mounting components | Compatible outgoing MCCB base plate and cover |
| Operating functionality | Manual switching and automatic overcurrent tripping |
| System type | Low-voltage electrical distribution |
| Application | Compatible ABB Protecta Power outgoing circuits |
The ABB EPX-A1C-040L3 is a 40 A single-pole thermal-magnetic MCCB with an LSC L3 connection arrangement. It is designed for compatible ABB Protecta Power outgoing distribution circuits and provides overload and short-circuit protection.
L3 identifies the specified connection variant within ABB's Protecta Power single-pole outgoing MCCB range. ABB also lists EPX-A1C-040L1 and EPX-A1C-040L2 versions. The correct variant should be selected according to the approved panelboard connection arrangement.
The EPX-A1C-040L3 has a 40 A current rating and a single-pole (1P) configuration. It belongs to the ABB Formula A1N125 circuit breaker family. The 125 A frame designation does not change the device's specified 40 A rating.
ABB's Protecta Power selection literature identifies the 40 A single-pole A1N125 outgoing MCCB with a 25 kA breaking-capacity classification. The applicable rated operational voltage and detailed breaking-capacity specification must be verified against the manufacturer's technical documentation before installation.
Yes. ABB's Protecta Power selection literature specifies that an MCCB base plate and cover are required with each outgoing device. The correct accessories must be selected for the panelboard and circuit breaker arrangement. The EPX-A1C-040L3 is not a complete enclosed distribution assembly on its own.
ABB Protecta Power provides coordinated low-voltage electrical distribution components for commercial and industrial installations. The EPX-A1C-040L3 combines a 40 A single-pole Formula A1N125 circuit breaker with thermal-magnetic protection, a published 25 kA breaking-capacity classification and an LSC L3 connection arrangement, giving electrical contractors and panel builders a clearly identified outgoing protection option for compatible Protecta Power assemblies.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.