Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
ABB EPX-A1C-025L2 1SDA123197R1 is a 25 A single-pole Formula A1N125 thermal-magnetic moulded case circuit breaker with an LSC L2 connection arrangement for outgoing circuit protection in compatible ABB Protecta Power distribution panelboards.
£194.77
The ABB EPX-A1C-025L2, manufacturer order code 1SDA123197R1, is a 25 A, single-pole moulded case circuit breaker (MCCB) from the ABB Formula A1N125 range, supplied with an LSC L2 connection arrangement for compatible ABB Protecta Power electrical distribution systems.
Designed for outgoing circuit protection, the EPX-A1C-025L2 combines a 25 A thermal-magnetic circuit breaker with a manufacturer-designated L2 connection configuration. It provides overload and short-circuit protection for suitable single-phase outgoing circuits within compatible three-phase distribution panelboards.
The product uses the ABB Formula A1N125 circuit breaker platform, with a 125 A frame designation and a 25 A rated current. Its thermal-magnetic protection technology provides automatic operation under qualifying overcurrent conditions without requiring an electronic trip unit or external power supply for the protection function.
As part of the ABB Protecta Power Devices product group, the EPX-A1C-025L2 supports professional distribution board construction using manufacturer-designated outgoing MCCBs and connection arrangements. Its L2 designation distinguishes it from the corresponding L1 and L3 variants, helping installers select the correct outgoing circuit configuration.
The ABB EPX-A1C-025L2 uses thermal-magnetic protection to respond to two principal types of overcurrent condition: sustained overloads and short circuits.
Thermal overload protection responds to excessive current flowing over a period of time. This protection helps prevent prolonged overcurrent conditions from causing unacceptable heating of cables and connected electrical equipment.
Magnetic short-circuit protection responds rapidly when current rises to the applicable magnetic trip threshold. This function helps interrupt qualifying short-circuit faults and limit their duration.
The manufacturer designation specifies a TMA thermal-magnetic trip arrangement. The exact available adjustment characteristics must be checked against the supplied circuit breaker documentation. They should not be assumed from the general characteristics of other ABB MCCB families.
The 25 A rated current is distinct from the 125 A frame designation. The frame designation identifies the circuit breaker platform, while the rated current identifies the current rating of this particular outgoing protective device.
ABB's Protecta Power selection information identifies the 25 A A1N125 single-pole MCCB with a 25 kA breaking capacity. The installation designer must confirm the applicable voltage, prospective fault current and protection coordination requirements before selecting the device.
The EPX-A1C-025L2 is specified with an LSC L2 arrangement. Within the ABB Protecta Power outgoing device range, the L1, L2 and L3 designations distinguish versions intended for the corresponding phase connection positions.
This is particularly important when constructing three-phase distribution panelboards with multiple single-pole outgoing circuits. Correct phase selection supports the intended electrical distribution arrangement and helps maintain consistency with the panelboard's designated outgoing connections.
ABB lists corresponding 25 A versions for the three phase designations:
These variants share the same specified current rating and circuit breaker family but differ in their designated phase connection arrangement. They should not be treated as interchangeable without confirming the required outgoing position and the applicable ABB installation instructions.
The LSC designation identifies the associated connection arrangement and should not be interpreted as an additional protective pole or a separate electronic protection function.
ABB Protecta Power is a low-voltage distribution system incorporating panelboard assemblies, incoming protective devices, outgoing MCCBs and installation accessories. The EPX-A1C-025L2 forms part of the outgoing MCCB selection range for suitable panelboard configurations.
ABB's Protecta Power documentation identifies a range of single-pole A1 outgoing MCCBs, including 20 A, 25 A, 32 A, 40 A, 50 A, 63 A, 80 A, 100 A and 125 A variants. This allows electrical designers to select an outgoing circuit breaker according to the requirements of the connected circuit.
The manufacturer also specifies that an MCCB base plate and cover are required with each outgoing device in the applicable Protecta Power arrangement. The necessary mounting and connection components must therefore be checked against the complete panelboard bill of materials.
ABB lists a maximum cable capacity of 50 mm² for its A1 single-pole outgoing device range. This is a family-level installation reference rather than a guarantee that every conductor type or terminal arrangement will accept that cross-section.
Actual cable suitability depends on the installed terminals, conductor material, termination method and applicable electrical installation requirements. The conductor must also be selected for the protected circuit's load, installation conditions and fault performance.
Before installation, the electrical designer should confirm the panelboard configuration, required L2 connection position, prospective short-circuit current, protective device coordination and compatibility with the selected outgoing mounting accessories.
| Product group | Protecta Power Devices |
|---|---|
| Distribution system | ABB Protecta Power |
| Circuit breaker family | ABB Formula |
| Circuit breaker designation | A1N125 |
| ABB order code | 1SDA123197R1 |
| Manufacturer description | EPX-A1C-025L2 A1N125 25A 1p + LSC L2 TMA |
| Product type | Moulded case circuit breaker with LSC connection arrangement |
| Rated current | 25 A |
| Frame designation | A1N125 |
| Frame size | 125 A |
| Number of poles | 1 |
| Pole configuration | Single-pole (1P) |
| Trip technology | Thermal-magnetic |
| Trip designation | TMA |
| Overload protection | Thermal |
| Short-circuit protection | Magnetic |
| Breaking capacity | 25 kA, as listed for the A1N125 25 A single-pole device |
| Connection arrangement | LSC |
| Phase designation | L2 |
| Installation function | Outgoing circuit protection |
| Compatible system | ABB Protecta Power distribution panelboards |
| Primary application | Low-voltage electrical distribution |
The ABB EPX-A1C-025L2 is a 25 A, single-pole Formula A1N125 moulded case circuit breaker with an LSC L2 connection arrangement, designed for outgoing circuit protection in compatible ABB Protecta Power distribution panelboards.
The L2 designation identifies the specified phase connection arrangement for this outgoing MCCB. ABB also lists corresponding L1 and L3 versions for other phase connection positions within compatible Protecta Power distribution assemblies.
The EPX-A1C-025L2 uses thermal-magnetic protection. Its thermal function provides overload protection, while its magnetic function provides short-circuit protection. The product is specified with a 25 A rated current and a TMA trip designation.
ABB's Protecta Power selection information lists the A1N125 25 A single-pole MCCB with a 25 kA breaking capacity. The applicable rated operational voltage and prospective fault current must be checked before installation.
All three are 25 A, single-pole A1N125 thermal-magnetic MCCB variants. The difference is their designated LSC phase connection arrangement: L1 for EPX-A1C-025L1, L2 for EPX-A1C-025L2 and L3 for EPX-A1C-025L3.
ABB Formula circuit breakers and Protecta Power distribution systems provide coordinated solutions for professional low-voltage electrical installations. The ABB EPX-A1C-025L2 combines a 25 A single-pole A1N125 thermal-magnetic MCCB with an LSC L2 connection arrangement, supporting dependable outgoing circuit protection in compatible commercial and industrial distribution panelboards.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.