Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
ABB EPX-A1C-020L2 (1SDA123196R1) 20 A single-pole Formula A1N125 thermal-magnetic outgoing MCCB with LSC L2 connection arrangement and 25 kA published breaking-capacity classification for compatible ABB Protecta Power distribution panelboards.
£194.77
The ABB EPX-A1C-020L2 is a 20 A single-pole moulded case circuit breaker (MCCB) supplied with an LSC L2 connection arrangement for compatible ABB Protecta Power electrical distribution panelboards. Identified by manufacturer order code 1SDA123196R1, this device belongs to the ABB Protecta Power Devices product group and provides dedicated outgoing circuit protection for professionally designed low-voltage distribution assemblies.
Based on the ABB Formula A1N125 circuit breaker platform, the EPX-A1C-020L2 incorporates thermal-magnetic protection to respond to overload and short-circuit conditions. Its 20 A current rating and single-pole (1P) configuration make it suitable for appropriately specified outgoing circuits requiring reliable overcurrent protection within a compatible Protecta Power panelboard.
ABB identifies the 20 A A1N125 outgoing MCCB with a 25 kA breaking-capacity classification in its Protecta Power selection literature. The product's L2 designation distinguishes its connection arrangement from the corresponding L1 and L3 versions. Together, the Formula A1N125 device, thermal-magnetic protection and LSC L2 arrangement provide a clearly specified solution for contractors, electrical designers and panel builders selecting ABB outgoing protective devices.
Outgoing circuit protection is an essential part of a professionally designed electrical distribution panelboard. Each outgoing protective device must be selected according to the intended load, conductor characteristics, installation conditions and prospective fault current. The ABB EPX-A1C-020L2 provides a 20 A single-pole MCCB solution for compatible Protecta Power assemblies, helping protect the connected circuit against overload and short-circuit conditions.
The product uses the ABB Formula A1N125 platform, a moulded case circuit breaker family designed for low-voltage electrical protection applications. The A1N125 designation identifies the circuit breaker family and frame classification, while the 20 A rating identifies the current rating of this particular device. The 125 A frame designation should not be confused with the protective device's specified 20 A rating.
The thermal-magnetic protection arrangement combines two complementary overcurrent protection functions. The thermal element responds to sustained overload conditions that can cause excessive heating in electrical conductors and equipment. The magnetic element responds to sufficiently high short-circuit currents, providing rapid protective tripping when the applicable operating threshold is reached.
ABB's Protecta Power selection literature identifies the 20 A single-pole A1N125 outgoing MCCB with a 25 kA breaking-capacity classification. This distinguishes it from the 16 A A1C125 outgoing device, which ABB lists with an 18 kA classification. The relevant breaking capacity must always be verified at the installation's operating voltage and against the exact circuit breaker documentation before specification.
The LSC L2 designation is an important part of the product reference. ABB provides three corresponding 20 A connection variants: EPX-A1C-020L1, EPX-A1C-020L2 and EPX-A1C-020L3. These references allow the correct connection arrangement to be selected for the designated outgoing position. The variants should not be substituted without checking the panelboard's approved connection configuration.
ABB's Protecta Power outgoing MCCB system uses coordinated mounting and cover components to integrate protective devices into the finished assembly. The manufacturer's selection literature states that an MCCB base plate and cover are required with each outgoing device. Consequently, the EPX-A1C-020L2 should be treated as an outgoing protective device for installation within a compatible distribution assembly, rather than a complete enclosed circuit protection solution.
The manufacturer's published Protecta Power information identifies a maximum cable capacity of 50 mm² for A1 single-pole devices. This figure describes the connection capability of the relevant device arrangement and is not a recommended conductor size for a 20 A circuit. The actual cable cross-section must be selected according to the electrical load, installation method, voltage drop, fault protection requirements and terminal compatibility.
When specifying the EPX-A1C-020L2, the electrical designer must verify the rated operational voltage, short-circuit breaking capacity, protective characteristics, conductor compatibility and panelboard installation requirements. Appropriate coordination with upstream and downstream protective devices should also be considered. Installation and commissioning must follow current ABB technical documentation and applicable electrical installation requirements.
| Product group | Protecta Power Devices |
|---|---|
| Compatible distribution range | ABB Protecta Power |
| ABB order code | 1SDA123196R1 |
| Manufacturer product description | A1N125 20A 1p + LSC L2 TMA |
| Product type | Moulded case circuit breaker (MCCB) with LSC connection arrangement |
| Device application | Outgoing circuit protection |
| Rated current | 20 A |
| Number of poles | 1P (single-pole) |
| Circuit breaker family | ABB Formula A1N125 |
| Frame family | 125 A |
| Protection technology | Thermal-magnetic |
| Trip designation | TMA |
| Overload protection | Thermal trip function |
| Short-circuit protection | Magnetic trip function |
| Published breaking-capacity classification | 25 kA; verify the applicable operational voltage and detailed ABB ratings |
| Connection arrangement | LSC L2 |
| Connection variant | L2 |
| Alternative connection variants | EPX-A1C-020L1 and EPX-A1C-020L3 |
| Published A1 single-pole maximum cable capacity | 50 mm², subject to terminal and installation requirements |
| Associated mounting components | Compatible outgoing MCCB base plate and cover |
| Operating functionality | Manual switching and automatic overcurrent tripping |
| System type | Low-voltage electrical distribution |
| Application | Compatible ABB Protecta Power outgoing circuits |
The ABB EPX-A1C-020L2 is a 20 A single-pole thermal-magnetic MCCB with an LSC L2 connection arrangement. It is designed for compatible ABB Protecta Power outgoing distribution circuits and provides overload and short-circuit protection.
L2 identifies the specified connection variant within ABB's Protecta Power single-pole outgoing MCCB range. ABB also lists EPX-A1C-020L1 and EPX-A1C-020L3 versions. The correct variant should be selected according to the approved panelboard connection arrangement.
The EPX-A1C-020L2 has a 20 A current rating and a single-pole (1P) configuration. It belongs to the ABB Formula A1N125 circuit breaker family. The 125 A frame designation does not change the device's specified 20 A rating.
ABB's Protecta Power selection literature identifies the 20 A single-pole A1N125 outgoing MCCB with a 25 kA breaking-capacity classification. The applicable rated operational voltage and detailed breaking-capacity specification must be verified against the manufacturer's technical documentation before installation.
Yes. ABB's Protecta Power selection literature specifies that an MCCB base plate and cover are required with each outgoing device. The correct accessories must be selected for the panelboard and circuit breaker arrangement. The EPX-A1C-020L2 is not a complete enclosed distribution assembly on its own.
ABB Protecta Power provides coordinated low-voltage electrical distribution components for commercial and industrial installations. The EPX-A1C-020L2 combines a 20 A single-pole Formula A1N125 circuit breaker with thermal-magnetic protection, a published 25 kA breaking-capacity classification and an LSC L2 connection arrangement, giving electrical contractors and panel builders a clearly identified outgoing protection option for compatible Protecta Power assemblies.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.