Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£223.52
The WAGO 704-5004 is a 16-channel relay output interface module designed to connect industrial PLC output signals to electrically isolated switching contacts. Part of WAGO's 704 Series system wiring range, it features a 20-pole male connector according to DIN 41651, 16 miniature switching relays, individual channel status indicators and double-deck PCB terminal blocks in a DIN-rail mounting carrier.
Each relay channel provides one changeover contact (SPDT), allowing compatible loads to be switched through normally open or normally closed contact arrangements. The module operates from a nominal 24 V DC control supply and supports a maximum continuous current of 5 A per channel, subject to the relay and installation ratings. With a maximum switching voltage of 250 V AC or 48 V DC, it provides a practical interface between low-voltage PLC control signals and industrial switching circuits.
The WAGO 704-5004 incorporates green LED indicators for individual relay channels and a yellow power supply LED, making it easier to monitor output activity and diagnose control system operation. Its standardised DIN 41651 ribbon cable connection, replaceable relay arrangement and accessible field-side terminals help simplify industrial panel wiring, commissioning and maintenance.
The WAGO 704-5004 converts control signals from a compatible PLC output interface into 16 independent relay contact outputs. Each channel provides a changeover contact, allowing the connected load to be switched using normally open or normally closed contacts as required by the application. This configuration is useful for controlling indicator devices, auxiliary relays, signalling circuits and other appropriately rated industrial electrical loads.
The module's 5 A maximum continuous current per channel applies regardless of the relay fitted, so replacement relay ratings must not be used to justify a higher module current. The maximum resistive switching capacities are 1,250 VA for AC circuits and 50 W for DC circuits. Actual permissible switching loads depend on the load type, voltage, power factor, switching frequency and relay contact characteristics.
The WAGO 704-5004 includes green LEDs for the individual relay channels, allowing technicians to observe relay activation during commissioning and fault finding. A separate yellow LED indicates the power supply status, helping distinguish control supply issues from individual output channel conditions.
The module also incorporates a 1 A internal supply fuse. This protects the module's supply circuit but does not replace suitable external protection for the switched load circuits. The standardised DIN 41651 connector helps organise PLC wiring, while the field-side terminal blocks allow load conductors to be accessed for inspection and maintenance.
The WAGO 704-5004 is designed for mounting on a standard 35 mm DIN rail inside an appropriate industrial electrical enclosure. Its 20-pole DIN 41651 connector must be connected using a compatible cable assembly with the correct pin assignment and orientation. The nominal 24 V DC control supply must remain within the specified ±10% operating range.
When connecting loads, observe the 5 A per-channel continuous current limit and the specified maximum AC and DC switching capacities. Inductive loads, such as contactor coils and solenoids, may require suitable suppression devices and additional switching derating. Appropriate circuit protection, conductor sizing, insulation separation and protection against accidental contact must be provided in accordance with the installation requirements.
| Type of electrical connection, field-sided | Spring clamp connection |
|---|---|
| Type of electrical connection, control sided | Other |
| Height | 105 mm |
| Number of poles | 64 |
| Rated voltage | 50 V |
| Width | 180 mm |
| Rated current | 5 A |
| Pollution degree | 2 |
| Depth | 105 mm |
| Mounting method | DIN rail (top hat rail) 35 mm |
| Manufacturer | WAGO |
| Series | 704 Series |
| Part number | 704-5004 |
| Product type | Relay output interface module for system wiring |
| Number of output channels | 16 |
| Output technology | Electromechanical miniature switching relays |
| Relay contact configuration | 1 changeover contact (SPDT) per channel |
| Nominal operating voltage | 24 V DC |
| Operating voltage range | ±10% |
| Calculated operating voltage range | 21.6–26.4 V DC |
| Maximum continuous current | 5 A per channel |
| Short-duration making capacity | 16 A for 2 ms |
| Maximum AC switching voltage | 250 V AC |
| Maximum DC switching voltage | 48 V DC |
| Maximum resistive AC switching power | 1,250 VA |
| Maximum resistive DC switching power | 50 W |
| Mechanical relay life | 30 × 106 switching operations |
| Relay contact material | AgNi 90/10 |
| Basic relay reference | WAGO 788-154 |
| System-side connector | DIN 41651 male |
| System-side number of poles | 20 |
| Field-side connection | Double-deck PCB terminal blocks |
| Maximum conductor cross-section | 2.5 mm² |
| Channel status indication | Green LED |
| Power supply status indication | Yellow LED |
| Internal supply fuse | 1 A |
| Individual relay output fuses | Not integrated |
| Rated insulation voltage | 50 V |
| Rated surge voltage | 0.8 kV |
| Dielectric strength between control and load circuits | 2.5 kV AC RMS for 1 minute |
| Dielectric strength between load circuits | 1 kV AC RMS for 1 minute |
| Net weight | Approximately 550 g |
| Compatible PLC family | Selected GE Fanuc Series 90-30 and RX3i modules |
| GE Fanuc Series 90-30 references | IC693MDL740, IC693MDL742, IC693MDL753 |
| GE Fanuc RX3i reference | IC694MDL753 |
The WAGO 704-5004 is a 16-channel relay output interface module designed to connect compatible PLC output signals to individually accessible relay switching contacts. It uses a 20-pole DIN 41651 male connector and provides one changeover contact per channel for industrial control applications.
The WAGO 704-5004 operates from a nominal 24 V DC supply with a tolerance of ±10%, corresponding to an operating range of 21.6–26.4 V DC. A yellow LED provides visual indication of the module's power supply status.
The module supports a maximum continuous current of 5 A per channel. Its maximum switching voltages are 250 V AC and 48 V DC, with maximum resistive switching powers of 1,250 VA AC and 50 W DC. The actual load must remain within all applicable relay and module ratings.
Yes. The WAGO 704-5004 features green LEDs for individual relay channels, a yellow power supply LED and an internal 1 A supply fuse. Individual relay output fuses are not integrated, so appropriate external load circuit protection must be provided.
The WAGO 704-5004 uses a 20-pole DIN 41651 male connector for system-side wiring and double-deck PCB terminal blocks for field-side load connections, accepting conductors up to 2.5 mm². It mounts on a 35 mm DIN rail and measures approximately 180 mm wide, 105 mm high and 105 mm deep.
WAGO system wiring modules provide practical solutions for connecting industrial PLC control signals to field-side electrical circuits. The WAGO 704-5004 combines 16 relay output channels, individual changeover contacts, integrated LED status indication, a 20-pole DIN 41651 connector and DIN-rail mounting in an organised interface assembly for industrial automation and electrical control systems.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.