Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
Finder 67.23.9.024.4500 is a 50 A Series 67 high-power PCB relay featuring a 24 V DC coil, three normally open AgSnO2 contacts, a minimum 5.2 mm contact gap, 2.7 W coil consumption and through-hole mounting for photovoltaic inverters and industrial power switching.
£28.92
The Finder 67.23.9.024.4500 is a high-power electromagnetic PCB relay from the Finder Series 67 range, developed for electrical switching in photovoltaic inverters, industrial power electronics, renewable energy equipment and power management systems. Featuring a 24 V DC operating coil and a three-pole normally open contact arrangement, the relay provides a practical switching interface between electronic control circuits and higher-power electrical loads.
The Finder Series 67 is designed for demanding applications requiring substantial contact capacity, electrical insulation and reliable mechanical switching. Its three-pole construction allows multiple contact paths to operate together under the control of a single electromagnetic coil. This makes the range particularly relevant to solar inverter manufacturers, industrial equipment designers and engineers developing power conversion assemblies.
The 67.23 configuration is designed for through-hole PCB mounting, allowing direct integration into electronic power assemblies. The .4500 contact variant should be checked against Finder's current product-specific documentation to establish its exact contact material, rated current, switching performance and any special construction characteristics. These details should not be assumed to be identical to the related 67.23.9.024.4300S version.
The Finder 67.23.9.024.4500 uses a 24 V DC electromagnetic coil to operate three normally open switching paths. When the coil is energised within its specified operating range, the contact mechanism closes the circuits. When coil power is removed, the non-latching relay returns the contacts to their normally open state.
This type of switching arrangement is useful in photovoltaic inverters, power conversion equipment and industrial electrical assemblies where an electronic controller must operate a higher-power circuit. The relay provides a mechanical switching interface, but the complete system must still incorporate appropriate protection, monitoring and control measures.
The three-pole contact system allows coordinated operation of multiple circuits. Whether those contacts may be connected in parallel for higher-current operation depends on the manufacturer's explicit approval for the exact variant. In particular, the special 100 A parallel-contact recommendation associated with the separate 67.23.9.024.4300S model must not automatically be applied to the 67.23.9.024.4500.
The through-hole PCB mounting arrangement supports integration into industrial power electronic equipment. Designers must consider copper track capacity, terminal current, thermal management, solder joint reliability, contact spacing and the electrical characteristics of the connected load. Inductive and capacitive loads may require additional switching protection because their inrush and interruption characteristics differ from resistive loads.
The Finder Series 67 range is associated with demanding electrical switching applications, but final component selection must be based on the exact .4500 variant's published ratings. The manufacturer's current documentation should be consulted before assigning a rated current, contact material, switching endurance or compliance claim to this part number.
Tick the specs you need, then view products that match.
| Device Type | Power Relay | |
|---|---|---|
| Terminal Type | PCB / pins | |
| Mounting Type | PCB | |
| Manufacturer | Finder | |
| Series | 67 Series High-Power Relays | |
| Manufacturer part number | 67.23.9.024.4500 | |
| Product type | Electromagnetic high-power PCB relay | |
| Relay operation | Electromechanical, non-latching | |
| Contact configuration | 3PST-NO (three-pole single-throw, normally open) | |
| Contact form | 3 Form A | |
| Number of poles | 3 | |
| Number of normally open contact paths | 3 | |
| Nominal coil voltage | 24 V DC | |
| Coil type | DC operated | |
| Contact material | Verify the .4500 variant against Finder documentation | |
| Rated contact current | Confirm for the exact ordering code | |
| Maximum switching voltage | Confirm for the exact ordering code and load category | |
| AC1 switching capacity | Confirm for the exact ordering code | |
| DC switching capacity | Dependent on circuit voltage, load characteristics and the manufacturer's switching curves | |
| Contact gap | Confirm against the applicable Series 67 variant drawing | |
| Coil consumption | Confirm for the 24 V DC .4500 version | |
| Coil resistance | Confirm for the 24 V DC .4500 version | |
| Insulation design | Series 67 reinforced coil-to-contact insulation architecture | |
| Dielectric strength | Verify the applicable product-specific insulation ratings | |
| Mounting type | Through-hole PCB mounting | |
| Terminal type | PCB solder terminals | |
| Installation method | Soldered into a suitably designed printed circuit board | |
| Environmental protection | Confirm the exact variant's relay protection category | |
| Operating temperature range | Confirm against the applicable Finder datasheet | |
| Application category | Photovoltaic power conversion, industrial power electronics and electrical switching equipment |
The Finder 67.23.9.024.4500 is a high-power electromagnetic PCB relay from the Finder Series 67 range. It is intended for electrical switching applications in equipment such as photovoltaic inverters, industrial power electronics and energy management systems, subject to the confirmed ratings of this particular variant.
The part number specifies a 24 V DC nominal operating coil. The exact operating voltage range, coil resistance and power consumption should be confirmed from Finder's product-specific documentation before designing the coil-drive circuit.
The 67.23 configuration uses three normally open contact paths, commonly described as 3PST-NO or 3 Form A. The three paths are operated by a common electromagnetic mechanism. Their permissible switching loads must be established from the exact product specification.
The Finder Series 67 includes high-current relays, but the exact rated contact current of the 67.23.9.024.4500 must be confirmed from its manufacturer documentation. A 100 A parallel-contact application is specifically associated with the separate 67.23.9.024.4300S version and should not be assumed to apply to the .4500 variant.
The relay is designed for through-hole PCB mounting with solder terminals. Installation requires a suitably designed printed circuit board with adequate conductor capacity, electrical clearances, mechanical support and thermal performance. The exact terminal layout and soldering requirements should be checked against Finder's dimensional drawings and installation instructions.
Finder Series 67 high-power relays provide electromechanical switching solutions for photovoltaic power conversion, industrial electrical equipment and energy management applications. With a 24 V DC coil, three-pole normally open construction and through-hole PCB mounting, the Finder 67.23.9.024.4500 offers a practical platform for engineered power switching systems when its exact contact ratings and installation requirements have been verified.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.