Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£258.71
The WAGO 787-1668 is a high-performance 8-channel electronic circuit breaker designed to provide selective overload and short-circuit protection for industrial 24 V DC distribution systems. Combining eight independently adjustable protection channels with integrated signalling and remote control capabilities, this compact WAGO circuit protection module is ideal for industrial automation, machinery control and electrical distribution cabinets.
Operating from a nominal 24 V DC supply with an input voltage range of 18–30 V DC, the WAGO 787-1668 provides eight protected outputs, each offering selectable current ratings of 2, 3, 4, 6, 8 or 10 A. Individual sealable selector switches allow protection settings to be matched to the current requirements of connected equipment.
The WAGO 787-1668 also features pulse-sequence communication, two active signalling outputs, remote channel control and eight illuminated three-colour operating buttons. With 99% typical efficiency, a switch-on capacity exceeding 50,000 µF per channel and time-delayed channel activation, it provides a practical solution for reliable, space-efficient DC circuit protection.
The WAGO 787-1668 provides electronic circuit protection for up to eight separate 24 V DC loads within a single module. Each channel features an independently selectable current rating, allowing connected equipment to receive protection appropriate to its electrical requirements.
When an overload or short circuit occurs, the affected channel is electronically disconnected according to its trip characteristic. This helps isolate faults within a DC distribution system and supports continued operation of unaffected circuits, provided the upstream power supply and protective arrangement are correctly coordinated.
The device's pulse-sequence communication capability offers additional diagnostic functionality. Through its active signalling outputs and compatible control equipment, individual channel status information can be communicated for monitoring purposes. The S1 remote input also supports reactivation of tripped channels and remote switching through the supported pulse-sequence control method.
Eight illuminated three-colour operating buttons allow personnel to identify channel conditions, switch outputs and reset tripped channels locally. This combination of local diagnostics and remote signalling can reduce the time required to identify faulty circuits during commissioning and maintenance.
With a switch-on capacitance exceeding 50,000 µF per channel, the WAGO 787-1668 accommodates compatible electronic loads with substantial input capacitance. Its time-delayed channel switching further helps manage the start-up of multiple loads connected to a common DC power supply.
For reliable operation, the upstream power supply capacity, conductor ratings, selected channel currents and total connected load must be assessed together. The WAGO 787-1668 is particularly well suited to control cabinets requiring multiple individually protected circuits, efficient fault diagnosis and centralised monitoring.
| Single-phase overcurrent possible | Yes |
|---|---|
| Current measuring range | 2 – 10 A |
| With detachable clamps | Yes |
| Type of electric connection | Spring clamp connection |
| Height | 127 mm |
| Min. adjustable delay-on energization time | 0.016 s |
| Width | 42 mm |
| Max. permitted delay-on energization time | 100 s |
| Depth | 142.5 mm |
| Manufacturer | WAGO |
| Series | 787 Series |
| Part number | 787-1668 |
| Product type | Electronic circuit breaker |
| Configuration | Eight-channel electronic circuit protection module |
| Protection technology | Electronic overcurrent protection |
| Nominal input voltage | 24 V DC |
| Input voltage range | 18–30 V DC |
| Number of channels | 8 |
| Nominal output voltage | 8 × 24 V DC |
| Output voltage range | 18–30 V DC, minus internal voltage drop |
| Voltage drop | ≤ 200 mV at 10 A, positive input |
| Selectable nominal output current | 2 / 3 / 4 / 6 / 8 / 10 A per channel |
| Maximum selectable current | 10 A per channel |
| Current setting method | Individual sealable selector switch |
| Factory current setting | 10 A per channel |
| Factory channel status | Switched on |
| Trip time | 16–100 s, depending on overload conditions |
| Switch-on capacitance | Greater than 50,000 µF per channel |
| Switch-on behaviour | Time-delayed channel switching |
| Channel switching delay | 50 ms to 5 s, load-dependent |
| Active current limitation | No |
| Current limitation | No |
| Status indication | Eight LEDs, green/red/orange |
| Green indication | Channel operating normally |
| Red indication | Channel tripped |
| Local operation | Individual illuminated channel buttons |
| Remote control input | S1 |
| Active signal outputs | S2 and S3 |
| Communication method | Pulse-sequence signalling |
| Individual channel status | Available via pulse sequence |
| Remote reset | Reactivation of tripped channels using a 15–30 V DC pulse |
| Minimum remote reset pulse duration | 500 ms |
| Remote switching | Switching of selected channels via pulse sequence |
| Typical efficiency | 99% |
| No-load power loss | ≤ 1.3 W |
| Power loss at 8 × 10 A | ≤ 20 W |
| Internal fuse | T 15 A per channel |
| Isolation voltage, connectors to housing | 0.5 kV DC |
| Protection class | III |
| Enclosure protection | IP20 according to EN 60529 |
| Reverse-voltage protection | No |
| Resistance to reverse feed | Up to 35 V DC |
| Parallel connection of individual channels | Not supported |
| Series connection of individual channels | Not supported |
| Positive input connection | Push-in CAGE CLAMP® |
| Positive input conductor cross-section | 0.5–10 mm² |
| Output and signal connection technology | CAGE CLAMP® |
| Output and signal conductor cross-section | 0.08–2.5 mm² |
| Mounting | 35 mm DIN rail |
| Installation | Industrial electrical control cabinets |
| Related group-signal variant | WAGO 787-1668/000-054 |
| Related IO-Link variant | WAGO 787-1668/000-080 |
The WAGO 787-1668 is an eight-channel electronic circuit breaker designed to protect industrial 24 V DC circuits against overloads and short circuits, with adjustable current settings, pulse-sequence signalling and remote control capabilities.
The WAGO 787-1668 provides eight independently protected output channels, allowing separate 24 V DC loads to be protected and managed individually.
Each channel can be adjusted to 2, 3, 4, 6, 8 or 10 A using its individual sealable selector switch. The factory setting is 10 A with channels switched on.
The circuit breaker operates from a nominal 24 V DC supply, with a permitted input voltage range of 18–30 V DC.
Yes. The WAGO 787-1668 provides active signalling outputs S2 and S3 and supports individual channel status reporting through pulse-sequence communication with compatible control equipment.
Yes. The S1 remote input supports reactivation of tripped channels using a 15–30 V DC pulse lasting at least 500 ms. The device also supports remote channel switching through pulse-sequence control.
Yes. The device supports a switch-on capacitance of greater than 50,000 µF per channel, making it suitable for compatible electronic loads with substantial input capacitance.
The specified overload trip time is 16–100 s, depending on the operating conditions and the magnitude of the overload. Short-circuit behaviour must be assessed using the manufacturer's applicable trip characteristic.
No. The standard WAGO 787-1668 uses pulse-sequence communication for signalling and remote control. The WAGO 787-1668/000-080 is the dedicated IO-Link variant.
The standard WAGO 787-1668 provides eight adjustable 24 V DC protection channels with active signal outputs and pulse-sequence communication. The 787-1668/000-054 provides a potential-free group signal contact instead of pulse-sequence communication.
No. The protected output channels are intended to operate independently. Parallel and series connections of individual channels are not supported.
The WAGO 787-1668 is designed for 35 mm DIN rail mounting inside a suitable industrial electrical cabinet. It uses WAGO spring-pressure connection technology, including a Push-in CAGE CLAMP® supply input and CAGE CLAMP® output and signalling connections.
The WAGO 787-1668 electronic circuit breaker combines eight independently adjustable 24 V DC protection channels, selectable 2–10 A current ratings, pulse-sequence communication, remote switching, active fault signalling and high capacitive-load capability. Its compact DIN rail design and comprehensive diagnostic features make it a dependable solution for industrial automation engineers, electrical panel builders and machine manufacturers requiring selective DC circuit protection.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.