Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£150.90
The WAGO 787-1664/000-100 is a compact and reliable 4-channel electronic circuit breaker designed to provide selective overcurrent protection for 12 V DC industrial power distribution systems. As part of the established WAGO 787 Series electronic circuit breaker range, this DIN rail-mounted protection module is specifically developed for industrial automation engineers, machine builders and control panel manufacturers requiring dependable protection of multiple DC load circuits.
Featuring four independently adjustable protection channels, the WAGO 787-1664/000-100 allows individual current settings of 2, 3, 4, 6, 8 or 10 A per channel. This flexibility enables engineers to configure circuit protection according to the requirements of connected equipment, helping isolate faulty circuits while maintaining the availability of unaffected loads. Integrated multicolour LED indicators and illuminated operating buttons provide convenient local switching, resetting and diagnostic functionality.
With a 12 V DC nominal input, an operating voltage range of 10–16 V DC and a compact 45 mm-wide DIN rail housing, this electronic circuit breaker is ideal for protecting industrial controllers, sensors, actuators and other DC-powered automation equipment. Its remote control input and active signalling outputs support integration with industrial monitoring systems, enabling efficient fault detection and remote circuit management.
Electronic circuit breakers such as the WAGO 787-1664/000-100 provide precise overcurrent protection for DC-powered industrial equipment. Unlike conventional protective arrangements that may disconnect an entire power supply when a fault occurs, this four-channel electronic protection module enables individual load circuits to be monitored and disconnected independently. This helps reduce unnecessary system interruptions and supports greater operational availability in industrial automation installations.
Each channel can be configured with a suitable current setting between 2 and 10 A, allowing engineers to match protection levels to connected equipment. When an overcurrent condition causes a channel to trip, the corresponding LED provides a clear visual indication. The integrated remote control and signalling interfaces also allow the device to communicate fault conditions and receive switching or reset commands from compatible control systems.
The WAGO 787-1664/000-100 is particularly useful in applications where multiple 12 V DC loads share a common power supply. Its time-delayed channel switching helps reduce simultaneous load connection, while its high capacitive switch-on capability supports industrial electronics with significant input capacitance. With a compact housing, high efficiency and maintenance-friendly connection technology, the device provides an effective solution for protecting modern industrial DC distribution networks.
| Single-phase overcurrent possible | Yes |
|---|---|
| Current measuring range | 2 – 10 A |
| With detachable clamps | Yes |
| Type of electric connection | Spring clamp connection |
| Height | 90 mm |
| Min. adjustable delay-on energization time | 0.016 s |
| Width | 45 mm |
| Max. permitted delay-on energization time | 100 s |
| Depth | 115.5 mm |
| Contains function DC-voltage overcurrent | Yes |
| Manufacturer | WAGO |
| Series | WAGO 787 Series |
| Model | 787-1664/000-100 |
| Product type | Electronic circuit breaker / DC electronic circuit protection module |
| Protection technology | Electronic overcurrent protection |
| Number of channels | 4 |
| Nominal input voltage | 12 V DC |
| Input voltage range | 10–16 V DC |
| Nominal output voltage | 4 × 12 V DC |
| Output voltage range | 10–16 V DC, less internal voltage drop |
| Adjustable output current | 2 / 3 / 4 / 6 / 8 / 10 A per channel |
| Maximum nominal current setting | 10 A per channel |
| Factory-default current setting | 10 A per channel |
| Current adjustment | Individual sealable selector switches |
| Voltage drop | ≤ 200 mV at input (+) |
| Switch-on capacity | > 50,000 µF per channel |
| Channel switch-on delay | Load-dependent, 50 ms to 5 s |
| Active current limitation | No |
| Typical efficiency | 99% |
| Power loss | ≤ 0.53 W at no load; ≤ 10 W at 4 × 10 A |
| Status indication | 4 × multicolour LEDs (green / red / orange) |
| Normal operation indication | Green LED |
| Tripped channel indication | Red LED |
| Remote control input | 1 × S1 |
| Active signalling outputs | 2 × S2 / S3 |
| Remote reset signal | 9–30 V DC pulse for at least 500 ms |
| Remote switching | Individual channel control via pulse sequence |
| Internal fuse | T 15 A per channel |
| Isolation voltage (connectors to housing) | 0.5 kV DC |
| Protection class | III |
| Protection rating | IP20 according to EN 60529 |
| Transient suppression | 33 V suppressor diode |
| Reverse voltage protection | No |
| Reverse-feed voltage resistance | ≤ 35 V DC |
| Parallel operation of individual channels | Not permitted |
| Series operation | Not permitted |
| Mean time between failures (MTBF) | > 500,000 hours according to IEC 61709 |
| Input (+) connection | Push-in CAGE CLAMP®, WAGO 831 Series |
| Input (+) conductor cross-section | 0.5–10 mm² |
| Input (+) stripping length | 13–15 mm |
| Input (−), output and signalling connections | CAGE CLAMP®, WAGO 721 Series |
| Output / signalling conductor cross-section | 0.08–2.5 mm² |
| Output / signalling stripping length | 8–9 mm |
| Mounting type | DIN 35 rail according to EN 60715 |
| Dimensions (H × W × D) | 90 × 45 × 115.5 mm |
| Weight | Approximately 170 g |
| Operating temperature | −25 to +70 °C, with derating where applicable |
| Storage temperature | −25 to +85 °C |
| Relative humidity | 5–96%, non-condensing |
| Pollution degree | 2 |
| Conformity and approvals | CE; UL and DNV approvals |
| Installation environment | Industrial electrical control cabinets and DC distribution panels |
The WAGO 787-1664/000-100 is a four-channel electronic circuit breaker used to protect individual 12 V DC electrical circuits against overcurrent conditions. It is designed for industrial automation systems, control panels and DC power distribution applications.
The device has four independently protected channels. Each channel can be individually configured, switched and monitored, allowing separate protection of multiple DC loads connected to a common power supply.
The WAGO 787-1664/000-100 operates with a nominal 12 V DC input and supports an operating voltage range of 10–16 V DC. It is specifically designed for 12 V DC systems rather than standard 24 V DC installations.
Each channel can be independently configured to 2, 3, 4, 6, 8 or 10 A using its selector switch. This enables protection settings to be matched to the requirements of individual connected loads.
Yes. The electronic circuit breaker includes a remote control input (S1) that allows tripped channels to be reactivated using a 9–30 V DC control pulse lasting at least 500 ms. Individual channels can also be switched remotely using the supported pulse-sequence control method.
Each channel has an integrated multicolour LED indicator. A green indication identifies normal channel operation, while a red indication identifies a tripped channel. Active signalling outputs also allow fault and channel status information to be communicated to external monitoring equipment.
Yes. Each channel supports a switch-on capacity greater than 50,000 µF, making the device suitable for compatible industrial electronic loads with significant input capacitance. The integrated time-delayed switching function also helps manage the connection of multiple loads.
No. The manufacturer specifies that parallel operation of individual channels is not permitted. Each channel must be used within its individual rated current setting, and series operation is also not permitted.
No. The WAGO 787-1664/000-100 is an electronic circuit protection device, not an AC/DC power supply. It requires a suitable external 12 V DC supply and provides independently protected DC outputs for connected equipment.
The device is designed for mounting on a standard 35 mm DIN rail inside industrial electrical control cabinets and DC distribution panels. Its IP20 protection rating and compact 45 mm width make it suitable for protected electrical installations.
WAGO electronic circuit breakers are designed to provide reliable and selective protection for industrial DC power distribution systems. Combining individually adjustable protection channels, clear LED diagnostics, remote switching capability and compact DIN rail installation, the WAGO 787-1664/000-100 offers machine builders and automation engineers a practical solution for protecting critical 12 V DC equipment while supporting efficient fault management and system availability.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.