Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£204.90
The WAGO 787-1664/000-080 is a compact, intelligent 4-channel electronic circuit breaker with IO-Link communication, designed to protect industrial 24 V DC control circuits against overloads and short circuits. Combining individually adjustable electronic protection with digital monitoring and remote channel control, this WAGO 787 Series device provides a flexible solution for modern industrial automation and DC power distribution systems.
Operating from a nominal 24 V DC input with an operating range of 18–30 V DC, the WAGO 787-1664/000-080 provides four independently protected outputs. Each channel supports current settings of 1, 2, 3, 4, 6, 8 or 10 A via IO-Link, while local selector switches provide settings of 1, 2, 4, 6 or 10 A. This combination allows protection levels to be configured locally or through a compatible IO-Link system.
The integrated IO-Link interface enables remote switching, individual channel status monitoring and current measurement. Four illuminated, three-colour operating buttons provide convenient local diagnostics, while time-delayed channel activation and a switch-on capacity exceeding 50,000 µF per channel support reliable operation with compatible industrial electronic loads.
The WAGO 787-1664/000-080 combines electronic overcurrent protection with digital communication to provide improved visibility and control of industrial 24 V DC distribution circuits. Each of its four channels can be assigned an individual current rating, enabling protection settings to be matched to the electrical characteristics of connected equipment.
The integrated IO-Link interface distinguishes this model from conventional electronic circuit breakers. Through a compatible IO-Link master, users can monitor the status and current consumption of individual channels, configure supported protection settings and switch selected outputs remotely. These capabilities help maintenance teams identify overloaded circuits and investigate changes in connected equipment.
Local operation remains straightforward. Each channel features an illuminated, three-colour operating button for switching, resetting and fault identification. Current settings can also be selected using the local switches, with available settings of 1, 2, 4, 6 and 10 A. Additional 3 A and 8 A settings are available through IO-Link configuration.
With a switch-on capacity exceeding 50,000 µF per channel, the WAGO 787-1664/000-080 can accommodate compatible electronic loads with significant input capacitance. Its time-delayed channel switching also helps manage the start-up of multiple loads connected to a common DC supply.
The device's 99% typical efficiency, compact 45 mm width and DIN rail mounting make it particularly suitable for industrial control cabinets where space, diagnostics and selective circuit protection are important. Correct operation requires appropriate coordination of the upstream power supply, channel settings, conductor sizes and connected loads.
| Single-phase overcurrent possible | Yes |
|---|---|
| Current measuring range | 1 – 10 A |
| With detachable clamps | Yes |
| Type of electric connection | Spring clamp connection |
| Height | 90 mm |
| Min. adjustable delay-on energization time | 0.016 s |
| Width | 45 mm |
| Max. permitted delay-on energization time | 100 s |
| Depth | 115.5 mm |
| Contains function DC-voltage overcurrent | Yes |
| Manufacturer | WAGO |
| Series | 787 Series |
| Part number | 787-1664/000-080 |
| Product type | Electronic circuit breaker with IO-Link |
| Protection technology | Electronic overcurrent protection |
| Communication interface | IO-Link |
| Nominal input voltage | 24 V DC |
| Input voltage range | 18–30 V DC |
| Total number of channels | 4 |
| Nominal output voltage | 4 × 24 V DC |
| Output voltage range | 18–30 V DC, minus internal voltage drop |
| Voltage drop | ≤ 200 mV at the positive input |
| Selectable output current via IO-Link | 1 / 2 / 3 / 4 / 6 / 8 / 10 A per channel |
| Selectable output current via local selector | 1 / 2 / 4 / 6 / 10 A per channel |
| Maximum selectable current | 10 A per channel |
| Factory current setting | 10 A per channel |
| Factory channel status | Switched off |
| Current adjustment | Local selector switch or IO-Link interface |
| Trip time | 16 ms to 100 s, load-dependent |
| Switch-on capacitance | Greater than 50,000 µF per channel |
| Switch-on behaviour | Time-delayed channel switching |
| Channel switching delay | 50 ms to 5 s, load-dependent |
| Active current limitation | No |
| Channel indication | Four LEDs, green/red/orange |
| Green LED | Channel operating normally |
| Red LED | Channel tripped |
| Local operation | Individual illuminated operating buttons |
| Digital status reporting | Individual channel status via IO-Link |
| Digital current measurement | Individual channel current measurement via IO-Link |
| Remote control | Switching on or off any number of channels via IO-Link |
| Typical efficiency | 99% |
| No-load power loss | ≤ 0.84 W |
| Power loss at 4 × 10 A | ≤ 10 W |
| Internal fuse | T 15 A per channel |
| Connector-to-housing isolation | 0.5 kV DC |
| Protection class | III |
| Protection rating | IP20 according to EN 60529 |
| Reverse-polarity protection | No |
| Resistance to reverse feed | Up to 35 V DC |
| Transient suppression | 33 V suppressor diode on input |
| Parallel connection of individual channels | Not permitted |
| Series operation | Not permitted |
| Pollution degree | 2 |
| MTBF | Greater than 500,000 hours according to IEC 61709 |
| Positive input connection | Push-in CAGE CLAMP®, WAGO 831 Series |
| Positive input conductor cross-section | 0.5–10 mm² |
| Positive input conductor size | 20–8 AWG |
| Positive input strip length | 13–15 mm |
| Negative input, output and signalling connections | CAGE CLAMP®, WAGO 721 Series |
| Output and signal conductor cross-section | 0.08–2.5 mm² |
| Output and signal conductor size | 28–12 AWG |
| Output and signal strip length | 8–9 mm |
| Mounting | 35 mm DIN rail |
| Operating temperature | −25 to +70 °C, with derating from +50 °C |
| Storage temperature | −25 to +85 °C |
| Relative humidity | 5–96%, non-condensing |
| Dimensions (W × H × D) | 45 × 90 × 115.5 mm |
| Weight | Approx. 170 g |
| Standards | EN 61000-6-2, EN 61000-6-3, UL 508 and UL 2367 |
| Marine approval | DNV |
| RoHS status | Compliant |
| GTIN/EAN | 4055143899239 |
The WAGO 787-1664/000-080 is a four-channel electronic circuit breaker with IO-Link designed to protect 24 V DC industrial control circuits against overloads and short circuits while providing digital channel monitoring and remote control.
The device provides four independently protected output channels. Each channel can be configured with an individual current setting and monitored through the IO-Link interface.
Each channel supports 1, 2, 3, 4, 6, 8 or 10 A when configured through IO-Link. The local selector switches provide 1, 2, 4, 6 or 10 A settings.
The IO-Link interface enables individual channel status reporting, current measurement, supported current-setting configuration and remote switching through a compatible IO-Link master.
The circuit breaker operates from a nominal 24 V DC supply, with an input voltage range of 18–30 V DC.
Yes. A compatible IO-Link system can switch individual channels on or off remotely, allowing selected outputs to be controlled without operating the local buttons.
Yes. The device supports individual channel current measurement via IO-Link, providing useful information for monitoring connected loads and investigating overload conditions.
Yes. Each channel supports a switch-on capacitance of greater than 50,000 µF, making the device suitable for compatible electronic loads with substantial input capacitance.
The trip time is load-dependent and ranges from 16 ms to 100 s. Actual disconnection time depends on the selected current setting and the magnitude of the overload.
No. Parallel connection of individual channels is not permitted, and series operation is also prohibited. Each channel must be wired according to the manufacturer's instructions.
The WAGO 787-1664/000-054 provides four adjustable 24 V DC protection channels with a potential-free group signal contact, while the 787-1664/000-080 adds IO-Link communication for individual channel monitoring, current measurement, remote switching and additional current-setting options.
The circuit breaker mounts on a 35 mm DIN rail and measures 45 × 90 × 115.5 mm. It uses Push-in CAGE CLAMP® technology for the positive input and CAGE CLAMP® connections for the negative input, outputs and signalling connections.
The WAGO 787-1664/000-080 electronic circuit breaker combines four independently adjustable 24 V DC protection channels, selectable 1–10 A current ratings, integrated IO-Link communication, individual current measurement, remote switching and high capacitive-load capability. Its compact DIN rail design and intelligent monitoring features make it a practical solution for industrial automation engineers, electrical panel builders and machine manufacturers requiring advanced DC circuit protection.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.