Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£163.45
The WAGO 787-1664/000-054 is a compact, 4-channel electronic circuit breaker designed to protect industrial 24 V DC control circuits against overloads and short circuits. Part of the WAGO 787 Series, this specialist configuration combines independently adjustable current protection, individual channel diagnostics and a potential-free group signal contact in a space-saving DIN rail-mounted enclosure.
Operating from a nominal 24 V DC supply with an input voltage range of 18–30 V DC, the WAGO 787-1664/000-054 provides four independently protected output channels. Each channel offers six selectable current settings of 2, 3, 4, 6, 8 or 10 A, allowing protection levels to be matched to individual loads.
The /000-054 specialty configuration features a potential-free group signal contact at terminals 13 and 14 for centralised fault monitoring, together with an S1 remote input for reactivating tripped channels. Four illuminated, three-colour operating buttons, time-delayed channel switching and a switch-on capacity exceeding 50,000 µF per channel make this electronic circuit breaker particularly suitable for industrial automation and distributed DC control systems.
The WAGO 787-1664/000-054 provides electronic protection for four separate 24 V DC circuits within a single compact module. Each channel can be assigned its own current rating, enabling installers to protect connected equipment according to its electrical requirements rather than using one common protection setting for multiple loads.
When an overload or short circuit occurs, the affected channel is disconnected according to the device's load-dependent trip characteristic. This helps isolate faulty circuits and supports continued operation of other protected loads, provided the upstream power supply and distribution system are correctly designed.
The /000-054 specialty configuration is particularly useful for control panels requiring a common fault indication. Its potential-free group signal contact at terminals 13 and 14 reports when one or more channels have tripped or been switched off. This signal can be incorporated into a compatible PLC, alarm or monitoring circuit for centralised diagnostics.
For remote fault recovery, the S1 control input allows tripped channels to be reactivated by applying a 15–30 V DC pulse for at least 500 ms. Individual illuminated buttons also provide convenient local switching, resetting and status identification during commissioning and maintenance.
With a switch-on capacity exceeding 50,000 µF per channel, the WAGO 787-1664/000-054 can accommodate compatible loads with substantial input capacitance. Time-delayed channel switching further helps manage start-up behaviour when several loads are connected to the same DC supply.
Its 45 mm width, 99% typical efficiency and WAGO spring-pressure terminal technology make the device a practical choice for compact industrial control cabinets where selective protection, fault signalling and straightforward maintenance are essential.
| Single-phase overcurrent possible | Yes |
|---|---|
| Current measuring range | 2 – 10 A |
| With detachable clamps | Yes |
| Type of electric connection | Spring clamp connection |
| Height | 90 mm |
| Min. adjustable delay-on energization time | 0.016 s |
| Width | 45 mm |
| Max. permitted delay-on energization time | 100 s |
| Depth | 115.5 mm |
| Contains function DC-voltage overcurrent | Yes |
| Manufacturer | WAGO |
| Series | 787 Series |
| Part number | 787-1664/000-054 |
| Product type | Electronic circuit breaker |
| Configuration | Four-channel specialty configuration with group signal contact |
| Protection technology | Electronic overcurrent protection |
| Nominal input voltage | 24 V DC |
| Input voltage range | 18–30 V DC |
| Total number of channels | 4 |
| Nominal output voltage | 4 × 24 V DC |
| Output voltage range | 18–30 V DC, minus internal voltage drop |
| Voltage drop | ≤ 200 mV at the positive input |
| Selectable output current | 2 / 3 / 4 / 6 / 8 / 10 A per channel |
| Maximum selectable current | 10 A per channel |
| Maximum sum of selected channel ratings | 40 A with all four channels set to 10 A; actual simultaneous loading depends on the supply and installation requirements |
| Factory current setting | 2 A per channel |
| Factory channel status | Switched off |
| Current setting method | Individual selector switch per channel |
| Trip time | 16 ms to 100 s, load-dependent |
| Switch-on capacitance | Greater than 50,000 µF per channel |
| Switch-on behaviour | Time-delayed channel switching |
| Channel switching delay | 50 ms to 5 s, load-dependent |
| Active current limitation | No |
| Channel status indication | Four illuminated LEDs/buttons, green/red/orange |
| Green LED | Channel operating normally |
| Red LED | Channel tripped |
| Local operation | Individual illuminated channel buttons |
| Remote control input | S1 |
| Remote reactivation | All tripped channels via 15–30 V DC pulse |
| Minimum remote pulse duration | 500 ms |
| Group signal output | Potential-free signal contact |
| Group signal terminals | 13 and 14 |
| Group signalling function | Common indication of tripped or switched-off channels |
| Typical efficiency | 99% |
| No-load power loss | ≤ 0.84 W |
| Power loss at 4 × 10 A | ≤ 10 W |
| Internal fuse | T 15 A per channel |
| Connector-to-housing isolation | 0.5 kV DC |
| Protection class | III |
| Protection rating | IP20 according to EN 60529 |
| Reverse-polarity protection | No |
| Resistance to reverse feed | Up to 35 V DC |
| Transient suppression | 33 V suppressor diode on input |
| Parallel connection of individual channels | Not permitted |
| Series operation | Not permitted |
| Pollution degree | 2 |
| MTBF | Greater than 500,000 hours according to IEC 61709 |
| Positive input connection | Push-in CAGE CLAMP®, WAGO 831 Series |
| Positive input conductor cross-section | 0.5–10 mm² |
| Positive input conductor size | 20–8 AWG |
| Positive input strip length | 13–15 mm |
| Negative input, output and signal connections | CAGE CLAMP®, WAGO 721 Series |
| Output and signal conductor cross-section | 0.08–2.5 mm² |
| Output and signal conductor size | 28–12 AWG |
| Output and signal strip length | 8–9 mm |
| Mounting | 35 mm DIN rail |
| Operating temperature | −25 to +70 °C |
| Dimensions (W × H × D) | 45 × 90 × 115.5 mm |
| Weight | Approx. 170 g |
| GTIN/EAN | 4055143318860 |
The WAGO 787-1664/000-054 is a four-channel electronic circuit breaker designed to protect 24 V DC industrial control circuits against overloads and short circuits, with independently adjustable current settings and a potential-free group signal contact.
The device provides four independently protected output channels. Each channel can be configured with its own current setting and operated individually.
Each channel can be set to 2, 3, 4, 6, 8 or 10 A using its individual selector switch. The factory setting is 2 A, with the channels initially switched off.
The circuit breaker operates from a nominal 24 V DC supply, with an input voltage range of 18–30 V DC.
The potential-free group signal contact at terminals 13 and 14 provides a common indication when one or more channels have tripped or been switched off, allowing compatible monitoring equipment to detect a protection event.
Yes. The S1 remote input can reactivate all tripped channels when supplied with a 15–30 V DC pulse lasting at least 500 ms.
Yes. Each channel supports a switch-on capacitance of greater than 50,000 µF, making the device suitable for compatible electronic loads with significant input capacitance.
The trip time is load-dependent and ranges from 16 ms to 100 s. The actual disconnection time depends on the selected current setting and the magnitude of the overload.
No. Parallel connection of individual channels is not permitted, and series operation is also prohibited. Each channel must be wired according to the manufacturer's instructions.
Both devices provide four adjustable 24 V DC protection channels rated from 2–10 A. The standard WAGO 787-1664 provides enhanced communication capability using pulse-sequence signalling, while the 787-1664/000-054 specialty configuration provides a potential-free group signal contact at terminals 13 and 14.
The circuit breaker mounts on a 35 mm DIN rail and measures 45 × 90 × 115.5 mm. It uses Push-in CAGE CLAMP® technology for the positive input and CAGE CLAMP® connections for the negative input, outputs and signalling terminals.
The WAGO 787-1664/000-054 electronic circuit breaker combines four independently adjustable 24 V DC protection channels, selectable 2–10 A current ratings, potential-free group fault signalling, remote reactivation and high capacitive-load capability. Its compact DIN rail design and reliable electronic protection make it a practical solution for industrial automation engineers, electrical panel builders and machine manufacturers requiring selective DC circuit protection.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.