Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£151.40
The WAGO 787-1664/000-004 is a compact and reliable four-channel electronic circuit breaker designed to protect 24 V DC power distribution systems in industrial automation, machine building and electrical control panels. Part of the WAGO EPSITRON 787 series, this DIN-rail-mounted protection device provides four independently adjustable output channels, helping protect PLCs, industrial controllers, sensors and other electronic equipment against overloads and short circuits.
Designed for industrial applications, the WAGO 787-1664/000-004 features selectable channel current ratings, time-delayed switching and illuminated three-colour channel indicators for local operation and fault diagnosis. Its remote control input supports channel switching and resetting, while active signal outputs provide status information for compatible monitoring systems. This special configuration is supplied with messaging disabled.
Operating from a 24 V DC supply with an input voltage range of 18–30 V DC, the WAGO 787-1664/000-004 offers selectable current ratings of 2, 3, 4, 6, 8 or 10 A per channel. The factory default is 2 A per channel, with the channels switched off. Its ability to accommodate capacitive loads up to 50,000 µF per channel, CAGE CLAMP connection technology and compact DIN-35 rail mounting make it suitable for industrial control cabinets and distributed DC power systems.
Electronic circuit breakers provide controlled protection for DC distribution circuits supplying industrial automation equipment. The WAGO 787-1664/000-004 divides a 24 V DC supply into four independently protected output channels, allowing current ratings to be selected for different connected loads. This arrangement helps limit the impact of an electrical fault on other equipment supplied by the same power distribution system.
The illuminated three-colour channel indicators provide convenient local status information for commissioning, switching and troubleshooting. The remote control input supports channel switching and reactivation of tripped circuits, while the active signal outputs provide electrical status signals for compatible external systems. The /000-004 variant is configured with messaging disabled, distinguishing it from the standard configuration.
Time-delayed channel switching helps distribute the starting demand of connected loads during power-up. The module supports capacitive loads up to 50,000 µF per channel and uses CAGE CLAMP connection technology for industrial wiring. Its IP20 protection rating requires installation inside an appropriate electrical enclosure. Because active current limitation and reverse-voltage protection are not provided, correct supply polarity, upstream protection and protective coordination are essential during system design.
| Single-phase overcurrent possible | Yes |
|---|---|
| Current measuring range | 2 – 10 A |
| With detachable clamps | Yes |
| Type of electric connection | Spring clamp connection |
| Height | 90 mm |
| Min. adjustable delay-on energization time | 0.016 s |
| Width | 45 mm |
| Max. permitted delay-on energization time | 100 s |
| Depth | 115.5 mm |
| Contains function DC-voltage overcurrent | Yes |
| Manufacturer | WAGO |
| Series | EPSITRON 787 |
| Model | 787-1664/000-004 |
| Product type | Electronic circuit breaker |
| Configuration | Special configuration with messaging disabled |
| Number of channels | 4 |
| Nominal input voltage | 24 V DC |
| Input voltage range | 18–30 V DC |
| Nominal output voltage | 4 × 24 V DC |
| Output voltage range | 18–30 V DC, subject to input voltage and voltage drop |
| Selectable nominal output current | 2, 3, 4, 6, 8 or 10 A per channel |
| Maximum nominal current per channel | 10 A |
| Maximum combined nominal channel current | 40 A across four channels, subject to supply capacity and operating conditions |
| Default current setting | 2 A per channel |
| Default channel state | Switched off |
| Voltage drop at input positive connection | Maximum 200 mV |
| Trip time | Approximately 16 ms to 100 s, load-dependent |
| Switch-on capacity | Up to 50,000 µF per channel |
| Channel switching sequence | Time-delayed, typically 50 ms to 5 s depending on the load |
| Active current limitation | No |
| Internal fuse | T 15 A per channel |
| Status indication | 4 illuminated green/red/orange LEDs |
| Remote control input | S1 |
| Remote reset signal | 15–30 V DC pulse, minimum 500 ms |
| Active signal outputs | S2 and S3 |
| Messaging configuration | Disabled |
| Connection technology, positive input | Push-in CAGE CLAMP |
| Connection technology, negative input, outputs and signalling | CAGE CLAMP |
| Positive input conductor cross-section | 0.5–10 mm² |
| Other terminal conductor cross-section | 0.08–2.5 mm² |
| Positive input strip length | 13–15 mm |
| Other terminal strip length | 8–9 mm |
| Mounting type | DIN-35 rail according to EN 60715 |
| Protection rating | IP20 according to EN 60529 |
| Protection class | III |
| Isolation voltage, connectors to housing | 0.5 kV DC |
| Reverse-voltage protection | No |
| Reverse-feed resistance | Up to 35 V DC |
| Transient suppression | 33 V suppressor diode |
| Parallel operation of individual channels | Not permitted |
| Series operation | Not permitted |
| Typical efficiency | 99% |
| Power loss | Maximum 0.84 W without load; maximum 10 W with four channels carrying 10 A each |
| Dimensions (W × H × D) | 45 × 90 × 115.5 mm from the upper edge of the DIN rail |
| Weight | Approximately 161 g |
| Operating temperature | −25 to +70 °C |
| Storage temperature | −25 to +85 °C |
| Relative humidity | 5–96%, without condensation |
| Temperature derating | Required at ambient temperatures of 50 °C and above |
| Pollution degree | 2 |
| MTBF | Greater than 500,000 h according to IEC 61709 |
| Standards and approvals | EN 61000-6-2, EN 61000-6-3, UL 508, UL 2367 and DNV |
| Conformity marking | CE |
| Country of origin | Germany |
| EAN | 4050821806417 |
The WAGO 787-1664/000-004 is a four-channel electronic circuit breaker designed to protect separate 24 V DC load circuits in industrial automation systems and electrical control cabinets.
Each channel has a selectable nominal current rating of 2, 3, 4, 6, 8 or 10 A. The factory default is 2 A per channel, with all channels switched off.
The WAGO 787-1664/000-004 is designed for a 24 V DC supply with an input voltage range of 18–30 V DC.
Yes. The remote control input supports switching channels and resetting tripped circuits using the specified voltage pulse and control sequences. Consult the manufacturer's instructions for the required signal timing.
The /000-004 special configuration has messaging disabled. The model retains its electronic circuit protection functions, while the specified messaging configuration distinguishes it from the standard version.
Yes. The specified switch-on capacity is up to 50,000 µF per channel. Actual suitability depends on the load characteristics, wiring and selected current settings.
No. Parallel operation of individual channels is not permitted. The channels must be used in accordance with the manufacturer's wiring and operating instructions.
The device is designed for DIN-35 rail mounting inside a suitable electrical enclosure. Its positive input uses push-in CAGE CLAMP technology, while the other terminals use CAGE CLAMP connections.
The WAGO 787-1664/000-004 has an IP20 protection rating and is intended for installation inside an appropriate electrical cabinet or enclosure.
The specified operating temperature range is −25 to +70 °C, with a storage temperature range of −25 to +85 °C. Derating is required at ambient temperatures of 50 °C and above.
WAGO EPSITRON electronic circuit breakers help protect and monitor industrial DC power distribution systems. The 787-1664/000-004 combines four independently adjustable protection channels, illuminated diagnostics, remote control functionality and DIN-rail mounting to support dependable power distribution in compatible industrial applications.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.