Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£130.14
The WAGO 787-1662/000-054 is a compact, 2-channel electronic circuit breaker designed to protect industrial 24 V DC control circuits against overloads and short circuits. Part of the WAGO 787 Series, this specialist configuration provides independently adjustable current protection, convenient local operation and remote fault monitoring for industrial automation and electrical distribution applications.
Operating with a nominal input voltage of 24 V DC and an input range of 18–30 V DC, the WAGO 787-1662/000-054 features two individually protected output channels. Each channel can be configured to 2, 3, 4, 6, 8 or 10 A using a selector switch, allowing protection settings to be matched to the requirements of connected equipment.
This particular /000-054 specialty configuration incorporates a potential-free group signal contact for reporting tripped or switched-off channels, together with a remote input for reactivating tripped channels. Its compact 45 mm width, multicolour LED indicators and high capacitive-load switching capability make it an effective solution for selective 24 V DC circuit protection.
The WAGO 787-1662/000-054 provides selective electronic protection for two separate 24 V DC circuits. Each channel has its own adjustable current setting, allowing connected loads to be protected according to their operating requirements. When a channel experiences an overload or short circuit, the breaker disconnects the affected output according to its load-dependent trip characteristic.
Unlike conventional fixed-rating protection devices, the WAGO 787-1662/000-054 provides six selectable current ratings per channel. This flexibility simplifies the design and maintenance of control cabinets containing different types of sensors, controllers, communication equipment and other DC loads.
The device is particularly useful for systems requiring centralised fault indication. Its potential-free group signal contact, connected through terminals 13 and 14, provides a common indication when a channel has tripped or been switched off. The remote input S1 also allows previously tripped channels to be reactivated using a suitable 15–30 V DC pulse lasting at least 500 ms.
High capacitive-load capability exceeding 50,000 µF per channel helps accommodate equipment with significant input capacitance. The load-dependent, time-delayed switching of individual channels further supports controlled start-up of multiple loads.
With 99% typical efficiency, a compact DIN rail enclosure and clear multicolour status indicators, the WAGO 787-1662/000-054 provides a practical combination of circuit protection, diagnostics and installation flexibility for industrial automation systems.
| Single-phase overcurrent possible | Yes |
|---|---|
| Current measuring range | 2 – 10 A |
| With detachable clamps | Yes |
| Type of electric connection | Spring clamp connection |
| Height | 90 mm |
| Min. adjustable delay-on energization time | 0.016 s |
| Width | 45 mm |
| Max. permitted delay-on energization time | 100 s |
| Depth | 115.5 mm |
| Contains function DC-voltage overcurrent | Yes |
| Manufacturer | WAGO |
| Series | 787 Series |
| Part number | 787-1662/000-054 |
| Product type | Electronic circuit breaker |
| Configuration | Specialty configuration with group signal contact |
| Protection technology | Electronic overcurrent protection |
| Nominal input voltage | 24 V DC |
| Input voltage range | 18–30 V DC |
| Total number of channels | 2 |
| Nominal output voltage | 2 × 24 V DC |
| Output voltage range | 18–30 V DC, minus internal voltage drop |
| Voltage drop | ≤ 200 mV at the positive input |
| Selectable output current | 2 / 3 / 4 / 6 / 8 / 10 A per channel |
| Maximum selectable current | 10 A per channel |
| Maximum combined nominal channel current | 20 A with both channels set to 10 A |
| Factory current setting | 2 A per channel |
| Factory channel status | Switched off |
| Current setting method | Individual selector switch per channel |
| Trip time | 16 ms to 100 s, depending on load |
| Switch-on capacitance | Greater than 50,000 µF per channel |
| Switch-on behaviour | Time-delayed channel switching |
| Channel switching delay | Load-dependent, approximately 50 ms to 5 s |
| Active current limitation | No |
| Channel indication | Two multicolour LED indicators, green/red/orange |
| Green LED | Channel operating normally |
| Red LED | Channel tripped |
| Local operation | Illuminated channel buttons |
| Remote control input | S1 |
| Remote reactivation | All tripped channels via 15–30 V DC pulse |
| Minimum remote pulse duration | 500 ms |
| Group signal output | Potential-free signal contact |
| Signal terminals | 13 and 14 |
| Group signalling function | Tripped or switched-off channel indication |
| Typical efficiency | 99% |
| No-load power loss | ≤ 0.84 W |
| Power loss at 2 × 10 A | ≤ 5.5 W |
| Internal fuse | T 15 A per channel |
| Connector-to-housing isolation | 0.5 kV DC |
| Protection class | III |
| Protection rating | IP20 according to EN 60529 |
| Reverse-polarity protection | No |
| Reverse-feed resistance | Up to 35 V DC |
| Transient suppression | 33 V suppressor diode on input |
| Parallel connection of individual channels | Not permitted |
| Series operation | Not permitted |
| Pollution degree | 2 |
| MTBF | Greater than 500,000 hours according to IEC 61709 |
| Positive input connection | Push-in CAGE CLAMP®, WAGO 831 Series |
| Positive input conductor cross-section | 0.5–10 mm² |
| Positive input conductor size | 20–8 AWG |
| Positive input strip length | 13–15 mm |
| Negative input, output and signal connections | CAGE CLAMP®, WAGO 721 Series |
| Output and signal conductor cross-section | 0.08–2.5 mm² |
| Output and signal conductor size | 28–12 AWG |
| Output and signal strip length | 8–9 mm |
| Mounting | 35 mm DIN rail |
| Operating temperature | −25 to +70 °C |
| Storage temperature | −25 to +85 °C |
| Relative humidity | 5–96%, non-condensing |
| Temperature derating | No derating specified |
| Dimensions (W × H × D) | 45 × 90 × 115.5 mm |
| Weight | Approx. 161 g |
| Standards | EN 61000-6-2, EN 61000-6-3, UL 508 and UL 2367 |
| Marine approval | DNV |
| RoHS status | Compliant |
| GTIN/EAN | 4055143373012 |
The WAGO 787-1662/000-054 is a 2-channel electronic circuit breaker designed to protect 24 V DC industrial control circuits against overloads and short circuits, with adjustable current settings and a group signal contact for fault monitoring.
The WAGO 787-1662/000-054 has two independently protected output channels. Each channel can be configured and operated individually.
Each channel can be set to 2, 3, 4, 6, 8 or 10 A using its individual selector switch. The factory setting is 2 A, with the channels initially switched off.
The circuit breaker operates from a nominal 24 V DC supply, with a permitted input voltage range of 18–30 V DC.
The potential-free group signal contact at terminals 13 and 14 provides a common indication when a channel has tripped or been switched off, allowing compatible monitoring equipment to detect a protection event.
Yes. The S1 remote input can reactivate all tripped channels when supplied with a 15–30 V DC pulse lasting at least 500 ms.
Yes. Each channel supports a switch-on capacitance of greater than 50,000 µF, making the device suitable for compatible electronic loads with significant input capacitance.
The trip time is load-dependent and ranges from approximately 16 ms to 100 s. The actual disconnection time depends on the selected current setting and the magnitude of the overload.
No. Parallel connection of individual channels is not permitted, and series operation is also prohibited. Each channel must be used according to the manufacturer's specified wiring arrangement.
Both devices provide two adjustable 24 V DC protection channels rated from 2–10 A. The standard WAGO 787-1662 provides individual active signal outputs, while the 787-1662/000-054 specialty configuration provides a potential-free group signal contact at terminals 13 and 14.
The circuit breaker mounts on a 35 mm DIN rail and measures 45 × 90 × 115.5 mm. It uses Push-in CAGE CLAMP® technology for the positive input and CAGE CLAMP® connections for the negative input, outputs and signalling terminals.
The WAGO 787-1662/000-054 electronic circuit breaker combines two independently adjustable 24 V DC protection channels, selectable 2–10 A current ratings, potential-free group fault signalling, remote reactivation and high capacitive-load capability. Its compact DIN rail design and reliable electronic protection make it a practical solution for industrial automation engineers, electrical panel builders and machine manufacturers requiring selective DC circuit protection.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.