Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
1STQ009122A0000 ABB PRVS7041 Rear Vertical Segregation Panel H700 W400 Internal Upper System pro E Power
ABB PRVS7041 (1STQ009122A0000) is a rear vertical segregation accessory for compatible ABB System pro E Power low-voltage switchboards, specified for a 700 mm nominal height, 400 mm nominal width and internal upper arrangement.
£45.50
Why Choose the ABB PRVS7041 System pro E Power Rear Vertical Segregation Panel?
The ABB PRVS7041 (1STQ009122A0000) is a dedicated rear vertical segregation accessory for ABB System pro E Power low-voltage electrical distribution switchboards. Designed for a nominal segregation arrangement of 700 mm in height and 400 mm in width, this component supports the creation of defined internal compartment boundaries within compatible modular switchboard assemblies.
The manufacturer's designation, SEGR.VERT.REAR H=700MM W=400MM INT.UP., identifies a rear vertical segregation component incorporating an internal upper arrangement. This configuration is intended for switchboard designs requiring a specific rear separation layout, allowing electrical panel builders to select a purpose-designated ABB accessory rather than adapting a generic enclosure barrier.
As part of the ABB System pro E Power range, the PRVS7041 is suitable for integration into compatible main distribution board structures. It supports organised internal separation around designated switchboard compartments and contributes to a coordinated modular assembly when installed alongside the appropriate enclosure frames, structural members and complementary segregation components.
For electrical engineers, switchboard manufacturers and installation contractors, the ABB PRVS7041 rear vertical segregation panel provides a clearly identified solution for the specified 700 mm × 400 mm nominal configuration. Its ABB manufacturer order code, 1STQ009122A0000, enables accurate specification, procurement and replacement identification.
Key Advantages
- Dedicated ABB segregation accessory: Designed for compatible ABB System pro E Power low-voltage switchboards.
- Rear vertical segregation: Supports physical separation within designated rear switchboard areas.
- 700 mm nominal height: Specified for the corresponding vertical segregation configuration.
- 400 mm nominal width: Designed for compatible switchboard arrangements requiring this configuration width.
- Internal upper arrangement: Identified by the manufacturer's INT.UP. designation.
- Modular system compatibility: Intended to work with appropriate System pro E Power enclosure and internal assembly components.
- Structured compartment separation: Helps panel builders establish defined physical boundaries within the switchboard.
- Accurate product selection: Clearly identified by model PRVS7041 and ABB order code 1STQ009122A0000.
- Professional panel-building applications: Suitable for industrial and commercial low-voltage distribution projects.
- System-based installation: Supports coordinated construction using manufacturer-specific switchboard accessories.
- Replacement identification: Provides a dedicated reference for compatible maintenance and refurbishment work.
Key Features
- ABB System pro E Power modular switchboard accessory.
- PRVS7041 rear vertical segregation component.
- ABB manufacturer order code: 1STQ009122A0000.
- Manufacturer designation: SEGR.VERT.REAR H=700MM W=400MM INT.UP.
- Vertical segregation orientation.
- Rear switchboard installation arrangement.
- 700 mm nominal segregation height.
- 400 mm nominal configuration width.
- Internal upper segregation arrangement.
- Designed for compatible low-voltage main distribution board assemblies.
- Supports internal compartment separation and organised enclosure layouts.
- Intended for use with appropriate ABB System pro E Power structural components.
- Suitable for integration into coordinated switchboard segregation schemes.
- Applicable to new switchboard construction and compatible accessory replacement.
- Intended for installation by qualified electrical panel-building personnel.
Rear Vertical Segregation for Modular Electrical Switchboards
The ABB PRVS7041 rear vertical segregation accessory is intended to support physical compartment separation within compatible System pro E Power electrical switchboards. Internal segregation is an important part of many low-voltage distribution board designs, particularly where busbars, functional units and connection areas must be arranged within clearly defined sections.
The PRVS7041 is specified for a rear vertical arrangement, meaning its intended segregation position is at the rear of the relevant switchboard configuration. Unlike horizontal separation components, which divide designated areas along a horizontal plane, a vertical segregation component is used to establish a separation boundary in the corresponding vertical arrangement.
Its 700 mm nominal height and 400 mm nominal width are important selection parameters. These measurements identify the intended segregation configuration; they should not automatically be treated as the exact external dimensions of the manufactured accessory. Panel builders should consult the relevant ABB technical drawing where precise component measurements, fixing positions or installation clearances are required.
The additional INT.UP. designation identifies an internal upper arrangement. This feature distinguishes the PRVS7041 from other rear vertical segregation components intended for different positions or switchboard configurations. The correct installation arrangement should be established from the relevant ABB System pro E Power assembly instructions.
By selecting a segregation accessory designed for the appropriate configuration, electrical panel builders can maintain a coordinated internal layout and reduce the need for non-standard modifications. The PRVS7041 should be used with the compatible ABB structural and segregation components specified for the complete assembly.
Supporting Internal Separation and IEC/EN 61439 Switchboard Design
Low-voltage switchboards can incorporate different levels of internal separation depending on their application and design requirements. Under the IEC/EN 61439 framework, segregation arrangements are commonly described using forms that distinguish the separation of busbars, functional units and terminals.
A rear vertical segregation component such as the ABB PRVS7041 can contribute to the physical barriers required by a particular switchboard arrangement. However, its manufacturer designation does not independently identify a specific segregation form, and the presence of one accessory does not establish the classification of the complete assembly.
For example, Form 2 arrangements involve separation between busbars and functional units, while Form 3 arrangements additionally separate individual functional units. The precise arrangement of terminals relative to busbars and functional units determines the applicable subdivision. Higher forms may require additional terminal separation.
The PRVS7041 should therefore be considered as one component within the complete segregation design. The final arrangement must account for all relevant barriers, supports, enclosure structures, cable connections and installed electrical equipment.
The accessory is a mechanical segregation component, not a circuit-breaker, busbar assembly or complete distribution board. It does not independently establish electrical current ratings, short-circuit withstand capability, ingress protection or IEC/EN 61439 conformity. These characteristics must be determined for the finished switchboard using the applicable ABB instructions and assembly verification procedures.
Selecting and Installing the ABB PRVS7041
When specifying the ABB PRVS7041, confirm that the intended enclosure belongs to the System pro E Power range and uses the appropriate rear vertical segregation arrangement. The nominal height of 700 mm, nominal width of 400 mm and internal upper configuration should all correspond to the relevant switchboard design.
The exact manufacturer order code, 1STQ009122A0000, should be used when purchasing the component or recording it in a project bill of materials. This helps distinguish the PRVS7041 from other PRVS-series accessories with different nominal dimensions or internal arrangements.
Before installation, the panel builder should verify the accessory's mounting position, required fixing components and compatibility with adjacent structural elements. Any additional segregation barriers needed to achieve the intended compartment layout must also be identified.
Installation should be performed by appropriately qualified personnel following the relevant ABB System pro E Power documentation. The completed switchboard must be assessed as a whole to ensure its mechanical arrangement and electrical performance meet the project's requirements.
Typical Applications
- ABB System pro E Power low-voltage main distribution switchboards.
- Rear vertical compartment segregation in compatible electrical enclosures.
- 700 mm high nominal segregation arrangements.
- 400 mm wide nominal switchboard configurations.
- Internal upper segregation arrangements.
- Industrial electrical power distribution boards.
- Commercial building main distribution assemblies.
- Modular low-voltage switchboard construction.
- Electrical distribution infrastructure in manufacturing facilities.
- OEM electrical panel-building projects.
- Internal separation arrangements using compatible ABB segregation accessories.
- Switchboard extensions where the required component configuration has been verified.
- Maintenance and refurbishment of compatible System pro E Power assemblies.
- Replacement of an existing ABB PRVS7041 accessory.
Technical Specifications
| Product group | System pro E Power |
|---|---|
| Series | PRVS |
| Manufacturer order code | 1STQ009122A0000 |
| Product designation | SEGR.VERT.REAR H=700MM W=400MM INT.UP. |
| Product type | Rear vertical segregation accessory |
| Product category | Electrical switchboard accessories |
| Accessory function | Internal compartment segregation |
| Segregation orientation | Vertical |
| Segregation location | Rear |
| Additional configuration | Internal upper arrangement |
| Nominal segregation height | 700 mm |
| Nominal configuration width | 400 mm |
| Compatible switchboard system | ABB System pro E Power |
| Application | Low-voltage electrical distribution assemblies |
| Installation type | Internal switchboard mounting |
| Primary function | Physical separation of designated rear switchboard areas |
| Physical component dimensions | Confirm against the applicable ABB technical drawing |
| Material | Confirm against the ABB product datasheet |
| Net weight | Confirm against the ABB product datasheet |
| Segregation form | Determined by the complete switchboard assembly |
Frequently Asked Questions
What is the ABB PRVS7041 used for?
The ABB PRVS7041 is a rear vertical segregation accessory for compatible ABB System pro E Power low-voltage electrical switchboards. It supports physical separation within designated rear compartment arrangements incorporating an internal upper configuration.
What is the ABB order code for the PRVS7041?
The official ABB manufacturer order code for the PRVS7041 is 1STQ009122A0000. This reference identifies the rear vertical segregation accessory specified for a nominal height of 700 mm and width of 400 mm with an internal upper arrangement.
What dimensions are specified for the ABB PRVS7041?
The PRVS7041 is specified for a 700 mm nominal segregation height and 400 mm nominal configuration width. These are installation configuration dimensions rather than independently confirmed overall physical measurements of the accessory.
What does SEGR.VERT.REAR H=700MM W=400MM INT.UP. mean?
The designation identifies a rear vertical segregation accessory with a nominal height of 700 mm, nominal width of 400 mm and an internal upper arrangement. It describes the intended segregation configuration within the compatible switchboard system.
Which ABB switchboard range is compatible with the PRVS7041?
The PRVS7041 belongs to the ABB System pro E Power product group. Compatibility with a particular enclosure and internal structure should be confirmed using the applicable ABB assembly documentation.
What is the purpose of rear vertical segregation in a switchboard?
Rear vertical segregation helps establish a physical boundary between designated internal switchboard areas. It contributes to organised compartment layouts and can form part of a complete internal separation arrangement involving busbars, functional units and other equipment.
Does the ABB PRVS7041 provide Form 3b or Form 4 segregation?
The PRVS7041 is an internal segregation accessory, but its designation does not independently specify Form 3b, Form 4 or another complete segregation form. The final classification depends on the complete switchboard design and correct installation of all required barriers and associated components.
Are the 700 mm and 400 mm measurements the physical dimensions of the panel?
Not necessarily. The 700 mm height and 400 mm width are the nominal configuration measurements stated in the manufacturer's designation. Exact manufactured component dimensions should be verified against the relevant ABB technical drawing.
Can the ABB PRVS7041 be used as a complete electrical enclosure?
No. The PRVS7041 is a mechanical internal segregation accessory, not a complete switchboard enclosure, busbar system or protective switching device. It must be installed with the appropriate compatible System pro E Power components.
What should be checked before installing the ABB PRVS7041?
Confirm the System pro E Power enclosure configuration, the required rear vertical segregation position, the 700 mm nominal height, the 400 mm nominal width and the internal upper arrangement. Mounting requirements and complementary components should be checked against ABB's assembly instructions.
Trusted by Electrical Panel Builders Worldwide
ABB System pro E Power accessories support professional modular low-voltage switchboard construction for industrial and commercial electrical distribution. The ABB PRVS7041 rear vertical segregation component provides a dedicated solution for panel builders and electrical engineers requiring a 700 mm high, 400 mm wide nominal rear segregation arrangement with an internal upper configuration in compatible System pro E Power assemblies.
