1STQ007192A0000 ABB PBWP8030 Bottom Kit Without Plinth 800 x 300 mm

Why Choose the ABB PBWP8030 Bottom Kit Without Plinth?

The ABB PBWP8030 (1STQ007192A0000) is a dedicated bottom enclosure installation kit without plinth, designed for compatible ABB System Pro E Power modular low-voltage switchboards and electrical distribution cabinets. This original ABB accessory provides a designated lower enclosure assembly configuration for professional switchboard construction where a plinth is not included in the specified bottom kit arrangement.

Identified by ABB as PBWP8030 — KIT BOT.WITH-OUT PLINTH W=800MM D=300MM, the product is specified for an 800 mm nominal enclosure width and 300 mm nominal enclosure depth. Its manufacturer designation identifies a bottom installation kit intended for a without-plinth configuration, distinguishing it from alternative enclosure base accessories and arrangements incorporating a separate plinth.

As part of the ABB System Pro E Power range, the PBWP8030 supports coordinated modular switchboard construction. It is suitable for consideration by electrical panel builders, switchboard manufacturers and installation engineers selecting lower enclosure components for compatible 800 mm wide distribution cabinets. Correct accessory selection helps ensure that the planned enclosure footprint, bottom assembly arrangement and associated ABB components are appropriately matched.

Key Advantages

• Original ABB System Pro E Power accessory for compatible modular low-voltage electrical switchboards.
• Dedicated bottom installation kit for the corresponding enclosure configuration.
• Without-plinth arrangement for installations where a plinth is not part of the specified bottom kit configuration.
• 800 mm nominal enclosure width for accurate cabinet accessory selection.
• 300 mm nominal enclosure depth for the designated switchboard footprint.
• Supports coordinated selection of lower enclosure components during switchboard construction.
• Helps distinguish non-plinth bottom assemblies from alternative cabinet base arrangements.
• Designed for integration with compatible ABB System Pro E Power modular enclosure components.
• Supports professional switchboard manufacturing, maintenance and refurbishment planning.
• ABB order code 1STQ007192A0000 enables precise product identification and procurement.

Key Features

• ABB System Pro E Power modular switchboard accessory.
• PBWP8030 manufacturer model designation.
• Bottom installation kit identified by the KIT BOT. designation.
• Without-plinth configuration identified by WITH-OUT PLINTH.
• 800 mm nominal cabinet width.
• 300 mm nominal cabinet depth.
• Designed for the lower section of compatible electrical enclosure structures.
• Supports coordinated modular switchboard assembly.
• Suitable for compatible low-voltage electrical distribution cabinet construction.
• Provides a defined ABB configuration for bottom accessory selection.
• Mounting details and fixing requirements are subject to the relevant ABB installation documentation.
• ABB manufacturer reference 1STQ007192A0000 for specification and replacement identification.

Engineered for 800 mm Wide System Pro E Power Bottom Assemblies Without a Plinth

The ABB PBWP8030 is specifically designated for the bottom section of a compatible System Pro E Power switchboard. The lower enclosure arrangement forms part of the overall cabinet construction and must be selected according to the enclosure dimensions, installation method and associated ABB structural components.

The manufacturer's KIT BOT. designation identifies the product as a bottom installation kit. This differentiates it from top panels, side panels, doors, plinth assemblies and other modular enclosure accessories that perform different functions within the switchboard structure. Selecting the correct bottom kit is an important part of maintaining the intended assembly configuration.

The WITH-OUT PLINTH designation is a defining characteristic of the PBWP8030. A plinth is a separate base arrangement used in certain electrical enclosure installations to raise the cabinet or provide a particular lower support configuration. The PBWP8030 is identified for a bottom assembly arrangement without a plinth as part of the designated kit configuration.

However, the without-plinth designation does not independently establish a particular floor-fixing method, load-bearing capacity, installation height or support arrangement. These characteristics depend on the complete switchboard structure and the applicable ABB assembly instructions. Any additional fixing or support components must be selected according to the manufacturer's requirements.

The specified 800 mm nominal width and 300 mm nominal depth identify the intended enclosure footprint. These dimensions are essential when matching the bottom kit to a compatible System Pro E Power cabinet, but they should not be interpreted as independently verified physical dimensions of each supplied component.

The 800 mm nominal width distinguishes the PBWP8030 from narrower bottom kits intended for different cabinet configurations. This distinction matters because enclosure accessories must correspond to the appropriate structural dimensions. Products with similar model designations should not be treated as interchangeable without checking the complete manufacturer reference and applicable compatibility information.

Likewise, the 300 mm nominal depth must be matched to the intended cabinet structure. A bottom kit designated for a different enclosure depth may have different mechanical interfaces or assembly requirements. The correct depth specification should therefore be confirmed during switchboard design and before ordering replacement components.

When planning a low-voltage electrical distribution cabinet, the bottom assembly should be considered alongside the enclosure frame, cable-entry arrangements, fixing points and any required protective components. The PBWP8030 provides the designated bottom kit configuration, while the precise assembly sequence and compatibility of supplementary accessories must be established from ABB's relevant technical drawings.

The supplied manufacturer description does not state an IP protection rating for the PBWP8030. Accordingly, no particular dust or water ingress protection classification should be attributed to the kit independently. The achieved protection rating of the finished switchboard depends on the complete enclosure design, including its panels, joints, cable entries and other installed components.

The manufacturer designation also does not specify the kit's material, surface finish, mechanical load capacity or exact supplied contents. These details should be verified against ABB documentation before installation, especially where the completed assembly must meet defined structural, environmental or project-specific requirements.

For professional panel builders, selecting the correct original ABB bottom kit supports consistent modular assembly and accurate project documentation. The 1STQ007192A0000 order code provides a precise reference for identifying the PBWP8030 without-plinth configuration during procurement, installation, maintenance and future replacement.

Typical Applications

• ABB System Pro E Power modular low-voltage switchboards.
• Compatible electrical distribution cabinets requiring a bottom installation kit.
• Switchboard configurations specified without a plinth.
• Industrial electrical power distribution assemblies.
• Commercial building electrical distribution cabinets.
• Electrical control and automation enclosures using compatible ABB components.
• Cabinet configurations with an 800 mm nominal width and 300 mm nominal depth.
• Professional electrical panel manufacturing and assembly.
• Projects requiring coordinated ABB lower enclosure accessories.
• Compatible switchboard maintenance and refurbishment.
• Replacement of matching System Pro E Power bottom installation components.