1STQ007177A0000 ABB PBWP4030 Bottom Kit Without Plinth 400 x 300 mm

Why Choose the ABB PBWP4030 Bottom Kit Without Plinth?

The ABB PBWP4030 (1STQ007177A0000) is a dedicated bottom enclosure installation kit without plinth, designed for compatible ABB System Pro E Power modular low-voltage switchboards and electrical distribution cabinets. This original ABB accessory provides a specified bottom assembly arrangement for professional electrical enclosure construction where a plinth is not part of the designated installation configuration.

Identified by ABB as PBWP4030 — KIT BOT.WITH-OUT PLINTH W=400MM D=300MM, the product is specified for a 400 mm nominal enclosure width and 300 mm nominal enclosure depth. Its manufacturer designation identifies a bottom installation kit intended for a without-plinth configuration, distinguishing it from alternative base accessories and cabinet arrangements incorporating a plinth.

Part of the ABB System Pro E Power range, the PBWP4030 supports coordinated modular switchboard construction. It is particularly relevant to electrical panel builders, switchboard manufacturers and installation engineers who need to select the correct lower enclosure components for a defined cabinet footprint while maintaining compatibility with the wider ABB assembly system.

Key Advantages

• Original ABB System Pro E Power accessory designed for compatible modular low-voltage electrical switchboards.
• Dedicated bottom installation kit for the corresponding ABB enclosure configuration.
• Without-plinth arrangement for installations where a plinth is not part of the specified bottom kit configuration.
• 400 mm nominal enclosure width for accurate cabinet accessory selection.
• 300 mm nominal enclosure depth for the designated switchboard footprint.
• Supports coordinated selection of lower enclosure components during switchboard assembly.
• Helps distinguish non-plinth bottom configurations from alternative cabinet base arrangements.
• Designed for integration with compatible ABB System Pro E Power modular enclosure components.
• Suitable for professional electrical panel manufacturing, maintenance and refurbishment planning.
• ABB order code 1STQ007177A0000 enables precise product identification and procurement.

Key Features

• ABB System Pro E Power modular switchboard accessory.
• PBWP4030 manufacturer model designation.
• Bottom installation kit identified by the KIT BOT. designation.
• Without-plinth configuration identified by WITH-OUT PLINTH.
• 400 mm nominal cabinet width.
• 300 mm nominal cabinet depth.
• Designed for the lower section of compatible electrical enclosure structures.
• Supports coordinated modular switchboard assembly.
• Suitable for low-voltage electrical distribution cabinet construction.
• Provides a defined ABB configuration for bottom accessory selection.
• Compatible mounting details and fixing requirements are determined by ABB's installation documentation.
• ABB manufacturer reference 1STQ007177A0000 for specification and replacement identification.

Designed for System Pro E Power Bottom Enclosure Assembly Without a Plinth

The ABB PBWP4030 is specifically designated for the bottom section of a compatible System Pro E Power switchboard. The lower enclosure arrangement forms part of the overall cabinet construction and must be selected in accordance with the enclosure dimensions, installation method and associated ABB structural components.

The manufacturer's KIT BOT. designation identifies the product as a bottom installation kit. This differentiates it from top panels, side panels, doors, plinth assemblies and other modular enclosure accessories that perform different functions within the switchboard structure.

The WITH-OUT PLINTH designation is a defining characteristic of the PBWP4030. A plinth is a separate base arrangement used in some switchboard installations to raise the enclosure or provide a particular support configuration. The PBWP4030 is identified for a bottom assembly arrangement without a plinth as part of the designated kit configuration.

However, the without-plinth designation does not independently confirm a particular floor-fixing method, load-bearing capacity or installation height. These characteristics depend on the complete cabinet construction and the applicable ABB assembly instructions. Any additional fixing or support components should be selected according to the manufacturer's requirements.

The specified 400 mm nominal width and 300 mm nominal depth identify the intended enclosure footprint. These dimensions are important when matching the bottom kit to the appropriate System Pro E Power cabinet, but they should not be interpreted as independently verified physical dimensions of each supplied component.

Compared with a bottom kit intended for a 200 mm nominal enclosure depth, the PBWP4030 is designated for a 300 mm nominal depth. This distinction matters during product selection because enclosure accessories must correspond to the correct cabinet configuration. Similar product codes should not be treated as interchangeable without confirming compatibility.

When designing an electrical distribution cabinet, the bottom assembly must be considered alongside the enclosure frame, cable-entry arrangements, mechanical fixing points and any required protective components. The PBWP4030 provides the designated bottom kit configuration, while the precise assembly details must be established from ABB's relevant technical drawings.

The supplied manufacturer description does not state an IP protection rating for the PBWP4030. Accordingly, no specific dust or water ingress protection classification should be attributed to this accessory independently. The achieved protection rating depends on the complete switchboard enclosure, including panels, joints, cable entries and other installed components.

Similarly, the manufacturer's designation does not specify the kit's material, surface finish, mechanical load capacity or exact supplied contents. These details should be verified against ABB documentation before installation, particularly where the completed switchboard must meet defined structural, environmental or project-specific requirements.

For professional switchboard builders, selecting the correct original ABB bottom kit supports consistent modular assembly and accurate project documentation. The 1STQ007177A0000 order code provides a precise reference for identifying the PBWP4030 without-plinth configuration during procurement, installation, maintenance and future replacement.

Typical Applications

• ABB System Pro E Power modular low-voltage switchboards.
• Compatible electrical distribution cabinets requiring a bottom installation kit.
• Switchboard configurations specified without a plinth.
• Industrial electrical power distribution assemblies.
• Commercial building electrical distribution cabinets.
• Electrical control and automation enclosures using compatible ABB components.
• Cabinet configurations with a 400 mm nominal width and 300 mm nominal depth.
• Professional electrical panel manufacturing and assembly.
• Projects requiring coordinated ABB lower enclosure accessories.
• Compatible switchboard maintenance and refurbishment.
• Replacement of matching System Pro E Power bottom installation components.