Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
1STQ007176A0000 ABB PBWP4020 Bottom Kit Without Plinth 400 x 200 mm
ABB PBWP4020 1STQ007176A0000 System Pro E Power bottom enclosure installation kit without plinth, designed for compatible low-voltage switchboards with a nominal cabinet width of 400 mm and depth of 200 mm.
£54.10
Why Choose the ABB PBWP4020 Bottom Kit Without Plinth?
The ABB PBWP4020 (1STQ007176A0000) is a dedicated bottom enclosure installation kit without plinth, designed for compatible ABB System Pro E Power modular low-voltage switchboards and electrical distribution cabinets. This original ABB accessory provides a specified bottom assembly configuration for professional electrical enclosure construction where a separate plinth arrangement is not included in the kit designation.
Identified by ABB as PBWP4020 — KIT BOT. WITH-OUT PLINTH W=400MM D=200MM, the product is intended for a 400 mm nominal enclosure width and 200 mm nominal enclosure depth. The manufacturer's designation identifies a bottom installation kit supplied in a without-plinth configuration, making it important to distinguish this product from alternative base assemblies and accessories intended for cabinets incorporating a plinth.
As part of the ABB System Pro E Power range, the PBWP4020 supports coordinated modular switchboard construction. It is particularly relevant to panel builders, electrical contractors and switchboard manufacturers who need to select the correct lower enclosure components for a defined cabinet footprint while maintaining compatibility with the wider ABB assembly system.
Key Advantages
- Original ABB System Pro E Power accessory for compatible modular electrical switchboards.
- Dedicated bottom installation kit for the corresponding enclosure configuration.
- Without-plinth design for applications where a plinth is not part of the specified bottom kit arrangement.
- Designed for a 400 mm nominal enclosure width.
- Specified for a 200 mm nominal enclosure depth.
- Supports coordinated selection of lower enclosure components during switchboard construction.
- Helps distinguish non-plinth bottom configurations from alternative cabinet base arrangements.
- Suitable for integration with compatible ABB System Pro E Power modular enclosure components.
- Supports professional switchboard assembly, maintenance and refurbishment planning.
- ABB order code 1STQ007176A0000 enables accurate product identification and procurement.
Key Features
- ABB System Pro E Power modular switchboard accessory.
- PBWP4020 manufacturer model designation.
- Bottom installation kit identified by the manufacturer's KIT BOT. designation.
- Without-plinth configuration identified by WITH-OUT PLINTH.
- 400 mm nominal cabinet width.
- 200 mm nominal cabinet depth.
- Designed for the lower section of compatible electrical enclosure structures.
- Supports coordinated modular switchboard assembly.
- Suitable for professional low-voltage electrical distribution cabinet construction.
- Provides a defined manufacturer configuration for base accessory selection.
- Compatible enclosure details and fixing requirements are determined by ABB's installation documentation.
- ABB manufacturer reference 1STQ007176A0000 for specification and replacement identification.
Designed for System Pro E Power Bottom Enclosure Assembly Without a Plinth
The ABB PBWP4020 is specifically identified as a bottom installation kit for compatible System Pro E Power switchboards. The lower section of an electrical enclosure is an important part of the overall cabinet arrangement, and the correct accessories must be selected according to the enclosure's dimensions, installation method and associated structural components.
The manufacturer's KIT BOT. designation identifies the product as a bottom kit. This distinguishes it from top panels, side panels, doors, plinth assemblies and other enclosure accessories that serve different functions within a modular switchboard structure.
The WITH-OUT PLINTH designation is a key product characteristic. A plinth is a separate base arrangement that may be used in certain switchboard installations to raise an enclosure or provide a defined lower support structure. The PBWP4020 is identified for a configuration without such a plinth as part of the designated bottom kit arrangement.
However, the without-plinth designation should not be interpreted as confirmation of a particular floor-fixing method, cabinet load rating or mounting height. These characteristics depend on the complete enclosure configuration and the installation requirements established by ABB.
The specified 400 mm nominal width and 200 mm nominal depth identify the intended cabinet footprint. These measurements are essential when matching the kit to compatible System Pro E Power enclosure components, but they do not independently confirm the physical dimensions of each supplied part or the overall assembled cabinet dimensions.
When planning a switchboard installation, the bottom assembly must be considered alongside the enclosure frame, cable-entry arrangements, floor interface and any required protective components. The PBWP4020 provides the manufacturer-designated bottom kit configuration, while the precise fixing method and any additional accessories should be determined from the applicable ABB technical drawings.
The supplied product description does not specify an IP protection rating for the PBWP4020. Consequently, no particular dust or water ingress protection level should be attributed to the kit alone. The protection rating of the completed switchboard depends on the full enclosure design, including its panels, joints, cable entries and other fitted components.
Similarly, the manufacturer designation does not establish the kit's material, finish, mechanical load capacity or exact package contents. These details should be verified before installation, particularly where the enclosure must meet defined environmental, structural or project-specific requirements.
For professional panel builders, using the correct ABB bottom kit helps maintain consistency with the intended modular assembly. The 1STQ007176A0000 order code provides a precise reference for identifying the PBWP4020 without-plinth configuration during design, procurement, assembly and future maintenance.
Typical Applications
- ABB System Pro E Power modular low-voltage switchboards.
- Compatible electrical distribution cabinets requiring a bottom installation kit.
- Switchboard configurations specified without a plinth.
- Industrial electrical power distribution assemblies.
- Commercial building electrical distribution cabinets.
- Electrical control and automation enclosures using compatible ABB components.
- Cabinet configurations with a 400 mm nominal width and 200 mm nominal depth.
- Professional switchboard manufacturing and panel assembly.
- Projects requiring coordinated ABB lower enclosure accessories.
- Compatible electrical enclosure maintenance and refurbishment.
- Replacement of matching System Pro E Power bottom installation components.
Technical Specifications
| Product group | System Pro E Power |
|---|---|
| Model / type | PBWP4020 |
| ABB order code | 1STQ007176A0000 |
| Manufacturer designation | KIT BOT. WITH-OUT PLINTH W=400MM D=200MM |
| Product type | Bottom enclosure installation kit |
| Product category | Electrical enclosure and switchboard accessories |
| Installation location | Bottom of compatible enclosure |
| Base configuration | Without plinth |
| Nominal enclosure width | 400 mm |
| Nominal enclosure depth | 200 mm |
| Compatible enclosure system | ABB System Pro E Power |
| Primary application | Low-voltage electrical distribution switchboards |
| Equipment classification | Modular switchboard bottom assembly accessory |
| Supplied components | Exact kit contents to be confirmed against ABB documentation |
Frequently Asked Questions
What is the ABB PBWP4020 1STQ007176A0000 used for?
The ABB PBWP4020 is a bottom enclosure installation kit designed for compatible ABB System Pro E Power low-voltage switchboards. It is specified for a 400 mm nominal cabinet width, 200 mm nominal cabinet depth and a configuration without a plinth.
What dimensions does the ABB PBWP4020 support?
The PBWP4020 is specified for a 400 mm nominal enclosure width and 200 mm nominal enclosure depth. These values identify the compatible cabinet configuration rather than independently confirmed external dimensions of the individual kit components.
What does WITH-OUT PLINTH mean in the ABB PBWP4020 designation?
WITH-OUT PLINTH identifies a bottom kit configuration without a plinth as part of the designated arrangement. It distinguishes the PBWP4020 from enclosure base configurations involving a plinth. Any separately required floor-mounting or support accessories must be confirmed against ABB's installation documentation.
Is the ABB PBWP4020 compatible with every System Pro E Power enclosure?
No universal compatibility should be assumed. The ABB PBWP4020 is specified for a compatible 400 mm wide and 200 mm deep System Pro E Power enclosure configuration without a plinth. The precise cabinet variants and assembly requirements should be verified using ABB's technical documentation.
Does the ABB PBWP4020 have an IP65 rating or include a plinth?
The manufacturer's designation identifies the PBWP4020 as a bottom kit without plinth, and it does not specify an IP65 rating. The ingress protection of the completed enclosure depends on the full switchboard assembly. The exact supplied components and any additional accessories should be confirmed using ABB's product documentation.
Trusted ABB Modular Switchboard Engineering
ABB System Pro E Power accessories support coordinated, modular and maintainable low-voltage electrical switchboard construction. The PBWP4020 bottom installation kit provides a dedicated without-plinth configuration for compatible 400 mm wide and 200 mm deep enclosures, supporting accurate component selection and professional switchboard assembly.
