Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
ABB PPFM1040 1STQ007051A0000 is a set of two front and rear plinth flanges for compatible System Pro E Power low-voltage switchgear enclosures, specified for a nominal height of 100 mm and width of 400 mm.
£55.46
The ABB PPFM1040 Front and Rear Plinth Flanges (1STQ007051A0000) are dedicated plinth accessories for compatible ABB System Pro E Power low-voltage switchgear enclosures. Identified by the manufacturer's description 2 F/R PLINTH FLANGES H=100MM W=400MM, this product is specified as a set of two front/rear plinth flanges with a nominal height of 100 mm and width of 400 mm.
Plinth components are important elements of electrical enclosure construction. They form part of the base arrangement beneath a switchgear cabinet, helping complete the intended mechanical structure and providing a defined interface between the enclosure and its installation environment. The ABB PPFM1040 is designed for use within compatible System Pro E Power plinth configurations.
The front and rear (F/R) designation identifies the intended positions of these flanges within the plinth assembly. Their specified 100 mm height and 400 mm width help panel builders select the appropriate components for the required enclosure dimensions and base configuration.
With manufacturer reference PPFM1040 and ABB order code 1STQ007051A0000, these plinth flanges provide an accurately identified solution for original switchboard construction, enclosure assembly, refurbishment and approved replacement work. They are accessories for a compatible plinth system rather than a complete switchgear cabinet or standalone plinth assembly.
The ABB System Pro E Power range provides modular enclosure solutions for low-voltage electrical distribution switchboards. These assemblies incorporate structural frames, panels, doors, mounting components and base accessories selected according to the requirements of the completed electrical installation.
A switchgear plinth is a base structure positioned beneath an electrical enclosure. Depending on the design, a plinth may contribute to cabinet positioning, installation access and the organisation of the enclosure's lower mechanical structure. Its exact load-bearing and fixing characteristics depend on the complete manufacturer-specified assembly.
The ABB PPFM1040 is identified as a set of front and rear plinth flanges. These components are intended to form part of the corresponding front and rear sections of a compatible System Pro E Power plinth arrangement. They must be selected alongside the correct associated plinth and enclosure components.
The manufacturer specifies H=100MM, identifying a nominal plinth height of 100 mm. This measurement is relevant when matching the flanges to the required base configuration. It should not be taken as confirmation of the total installed cabinet height or the complete dimensions of every supplied component.
The designation W=400MM identifies a nominal width of 400 mm. Selecting the correct width is important because plinth components must correspond to the intended cabinet arrangement and adjoining structural elements. A flange set specified for 400 mm should not automatically be substituted for a component intended for another enclosure width.
The product description begins with 2 F/R PLINTH FLANGES, identifying two front/rear plinth flanges. This is the manufacturer-stated component quantity. However, it does not establish that the package includes a complete plinth, side components, fixing hardware or floor-anchoring accessories. Any additional items required for installation should be confirmed against the relevant ABB bill of materials.
Correct plinth assembly is important for the mechanical integrity of the completed switchboard. The enclosure must be installed on an appropriate supporting surface, with any required fixing or anchoring arrangements selected according to the switchgear manufacturer's instructions and the site installation requirements.
Plinth flanges should not be assumed to provide a specific load capacity, seismic performance, ingress protection rating or mechanical impact rating independently of the completed enclosure. Such characteristics depend on the complete assembly, its supporting structure and the applicable verification documentation.
Low-voltage switchgear assemblies may be designed and verified in accordance with BS EN IEC 61439. The mechanical strength and installation suitability of the completed assembly depend on the correct combination of its enclosure components, internal equipment and mounting arrangements.
For new installations or replacement work, confirm the PPFM1040 product reference, ABB order code 1STQ007051A0000, two-flange quantity, front/rear designation, 100 mm height and 400 mm width against the applicable System Pro E Power plinth configuration drawings.
The ABB PPFM1040 is a set of front and rear plinth flanges for compatible ABB System Pro E Power switchgear enclosures. The product is specified for a nominal plinth height of 100 mm and width of 400 mm.
The ABB order code is 1STQ007051A0000. The product reference is PPFM1040, and it belongs to the ABB System Pro E Power product group.
The manufacturer's description specifies 2 F/R PLINTH FLANGES, identifying two front/rear plinth flanges. The inclusion of additional fixing hardware or other plinth accessories should be confirmed using ABB's supply documentation.
F/R means front/rear. It identifies the intended positions of the flanges within a compatible System Pro E Power plinth assembly.
H=100MM identifies a nominal plinth height of 100 mm. This is a configuration measurement and does not establish the total height of the completed switchgear enclosure.
W=400MM identifies a nominal width of 400 mm for the intended plinth configuration. The exact external dimensions and fixing positions of the individual flanges should be checked against the applicable ABB technical drawings.
The PPFM1040 belongs to the ABB System Pro E Power range. It should be used with enclosure and plinth configurations that specifically require this reference and match the designated 100 mm height and 400 mm width.
No. The ABB PPFM1040 is identified as a set of two front/rear plinth flanges, not a complete plinth assembly. Other structural components, mounting accessories or fixings may be required depending on the enclosure configuration.
The manufacturer's supplied description does not establish the exact material, surface finish or coating of the ABB PPFM1040. These details should be confirmed using the relevant ABB product documentation or technical drawings.
Yes, where the existing System Pro E Power plinth assembly specifically requires ABB PPFM1040. Confirm the original reference, flange positions, nominal dimensions and mounting arrangement before replacement.
Confirm the ABB order code 1STQ007051A0000, product reference PPFM1040, quantity of two flanges, front/rear position, 100 mm height and 400 mm width. Check the relevant System Pro E Power plinth parts list for compatibility and any additional required components.
ABB System Pro E Power enclosure accessories support the construction, maintenance and refurbishment of professionally engineered low-voltage electrical distribution switchboards. The ABB PPFM1040 Front and Rear Plinth Flanges provide manufacturer-identified components for compatible 100 mm-high, 400 mm-wide plinth arrangements, helping panel builders and maintenance engineers select the correct accessories for their specified enclosure base configuration.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.