Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
1STQ002035B0000 ABB PTAB3070 System pro E Power IP65 Blind Internal Arc Top Panel 300 x 700mm
ABB PTAB3070 System pro E Power IP65-designated blind internal arc top panel, order code 1STQ002035B0000, with a nominal width of 300 mm and depth of 700 mm for compatible low-voltage switchgear enclosures.
£115.13
Why Choose the ABB PTAB3070 System pro E Power IP65 Blind Internal Arc Top Panel?
The ABB PTAB3070 is a dedicated IP65 blind internal arc top panel within the ABB System pro E Power range. Specified for a nominal width of 300 mm and depth of 700 mm, this accessory is intended for compatible low-voltage switchgear enclosure arrangements requiring the manufacturer's designated blind top configuration.
As part of the ABB System pro E Power modular switchgear platform, the PTAB3070 supports the construction of electrical distribution cabinets with appropriately selected top enclosure components. Its manufacturer description, IP65 BLIND IN.ARC TOP, identifies both an IP65 protection designation and an internal arc top configuration. These characteristics make correct component selection particularly important when designing switchgear assemblies with specified enclosure protection and internal arc requirements.
Identified by ABB order code 1STQ002035B0000, the PTAB3070 provides a manufacturer-specific solution for professional panel builders and switchgear manufacturers. Its 300 mm width, 700 mm depth and blind top designation enable accurate selection for compatible System pro E Power cabinet configurations. The final enclosure protection and internal arc performance depend on the complete assembly design, associated components and applicable verification.
Key Advantages
- ABB System pro E Power compatibility: Part of ABB's modular low-voltage switchgear enclosure platform.
- IP65 designation: Identified by ABB for applications requiring the specified enclosure protection configuration.
- Internal arc top configuration: Manufacturer-designated IN.ARC accessory for compatible switchgear arrangements.
- Blind top design: Provides a designated top covering component without a specified equipment opening.
- 300 mm nominal width: Matches the manufacturer's W=300 dimensional specification.
- 700 mm nominal depth: Matches the manufacturer's D=700 dimensional specification.
- Modular enclosure integration: Supports coordinated construction using compatible System pro E Power components.
- Application-specific selection: Helps distinguish the required top accessory from alternative cabinet covers.
- Professional switchgear construction: Relevant to industrial and commercial electrical distribution projects.
- Accurate procurement: Dedicated ABB model and order code support precise component identification.
Key Features
- ABB System pro E Power enclosure accessory.
- PTAB3070 manufacturer product designation.
- 1STQ002035B0000 ABB order code.
- IP65 manufacturer protection designation.
- Blind top panel configuration.
- IN.ARC internal arc configuration designation.
- 300 mm nominal width.
- 700 mm nominal depth.
- Intended for compatible switchgear top enclosure arrangements.
- Supports modular low-voltage electrical distribution cabinet construction.
- Designed for use with appropriately selected System pro E Power structural and enclosure components.
- Suitable for professional switchgear manufacturing and electrical panel building.
Specification note: The manufacturer description confirms the IP65 designation, blind internal arc top configuration and nominal width and depth. It does not specify the panel material, finish, thickness, fixing hardware, gasket arrangement or individual internal arc test classification. These details should be confirmed using the applicable ABB technical and assembly documentation.
Reliable Top Enclosure Integration for IP65 Switchgear Arrangements
Top enclosure components are important elements of modular low-voltage switchgear construction. They help complete the cabinet structure and provide the intended covering arrangement for the upper section of the assembly. Where an installation requires a specified degree of ingress protection, the top panel must be selected together with compatible enclosure components and installed in accordance with the manufacturer's instructions.
The ABB PTAB3070 is designated as an IP65 blind internal arc top with nominal dimensions of 300 mm wide by 700 mm deep. Under IEC 60529, an IP65 classification denotes protection against dust ingress and water jets under defined test conditions. However, the IP65 designation of this accessory does not independently establish the protection rating of an assembled cabinet. The complete enclosure must use compatible components and meet the applicable installation and verification requirements.
The IN.ARC designation identifies the product as part of an internal arc top configuration. Internal arc performance is an assembly-level consideration involving the enclosure structure, equipment arrangement, fault conditions and verified design. The PTAB3070 should therefore be used only in the appropriate ABB System pro E Power configuration, following the applicable assembly instructions. The completed switchgear should be assessed against relevant IEC 61439 requirements and any specified internal arc performance criteria.
Typical Applications
- ABB System pro E Power low-voltage switchgear assemblies.
- Compatible switchgear cabinets requiring an IP65-designated top accessory.
- Internal arc switchgear configurations specified for the IN.ARC top arrangement.
- Blind top coverage for compatible electrical distribution cabinets.
- Cabinet configurations requiring a nominal width of 300 mm.
- Cabinet configurations requiring a nominal depth of 700 mm.
- Industrial electrical distribution switchboards.
- Commercial and infrastructure low-voltage distribution installations.
- OEM switchgear manufacturing and professional electrical panel building.
Technical Specifications
| Product range | System pro E Power |
|---|---|
| ABB order code | 1STQ002035B0000 |
| Product type | Blind internal arc top panel |
| Manufacturer description | IP65 BLIND IN.ARC TOP W=300MM D=700MM |
| Manufacturer IP designation | IP65 |
| Panel configuration | Blind top |
| Internal arc designation | IN.ARC |
| Nominal width (W) | 300 mm |
| Nominal depth (D) | 700 mm |
| Installation location | Top of compatible switchgear enclosure |
| Compatible switchgear range | ABB System pro E Power |
| Application | Top enclosure coverage in compatible low-voltage switchgear assemblies |
| Product category | Switchgear top panels and enclosure accessories |
Frequently Asked Questions
What is the ABB PTAB3070 used for?
The ABB PTAB3070 is an IP65-designated blind internal arc top panel intended for compatible ABB System pro E Power low-voltage switchgear enclosures. It provides a manufacturer-specific top covering component for the applicable cabinet configuration.
What are the dimensions of the ABB PTAB3070?
The PTAB3070 has a specified nominal width of 300 mm and depth of 700 mm. These dimensions are identified in the ABB manufacturer description as W=300MM and D=700MM.
What does IP65 mean for the ABB PTAB3070?
IP65 is the ingress protection designation included in ABB's description of the PTAB3070. Under IEC 60529, IP65 denotes protection against dust ingress and water jets under defined test conditions. The completed switchgear enclosure must be correctly assembled and verified to establish its overall IP rating.
What does IN.ARC mean in the ABB PTAB3070 description?
IN.ARC is ABB's internal arc configuration designation for this top accessory. It identifies the component for compatible internal arc switchgear arrangements but does not, by itself, establish an internal arc classification or withstand rating for the completed assembly.
Can the ABB PTAB3070 be installed on any System pro E Power cabinet?
The PTAB3070 belongs to the ABB System pro E Power range, but compatibility depends on the specific cabinet dimensions, top structure, IP65 arrangement and internal arc configuration. The applicable ABB assembly documentation should be checked before installation.
Designed for Professional Switchgear and Panel Building
ABB System pro E Power enclosure accessories support the construction of coordinated modular low-voltage switchgear assemblies. The PTAB3070 provides an IP65-designated blind internal arc top component for compatible 300 mm by 700 mm cabinet configurations, helping professional panel builders select the correct enclosure accessory for the intended switchboard design.
