Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
Partex ECHS216GREY is grey 2:1 heat shrink tubing with a nominal supplied diameter of 1.6 mm, a recovered diameter of 0.8 mm and a total length of 150 m for electrical insulation, cable identification and wire protection.
£30.54
The Partex ECHS216GREY is a versatile grey 2:1 heat shrink tubing designed for electrical wire insulation, cable identification, conductor protection and professional wiring applications. Featuring a nominal supplied diameter of 1.6 mm and a nominal fully recovered diameter of 0.8 mm, this heat shrink sleeving provides a neat, close-fitting covering when correctly heated around suitably sized wires and components.
The 2:1 shrink ratio allows the tubing to recover to approximately half its original internal diameter when exposed to suitable heat. This enables the sleeving to conform around compatible electrical conductors, small cable joints and wiring assemblies, providing an additional insulating layer while helping protect against abrasion and general handling wear.
Supplied in a generous 150 m pack, the ECHS216GREY is particularly suitable for electrical contractors, panel builders, equipment manufacturers and maintenance engineers who require consistent heat shrink sleeving for repeated installation tasks. Its neutral grey finish is well suited to organised wiring systems, electrical control panels and professional cable management applications.
The Partex ECHS216GREY is designed to create a close-fitting protective sleeve around small wires and compatible electrical components. The tubing is positioned over the required section before heat is applied evenly using suitable hot-air equipment. As it warms, the material contracts around the underlying cable or component, helping produce a tidy insulating cover and a professional finish.
With a nominal diameter of 1.6 mm before shrinking and 0.8 mm after full recovery, this product is intended for applications requiring fine heat shrink sleeving. The tubing should be selected so that it fits over the component before heating and contracts sufficiently to grip it afterwards. Its 150 m supply length allows installers to cut sleeves to the required dimensions, helping reduce waste during repetitive electrical assembly and maintenance work.
Tick the specs you need, then view products that match.
| Supply Format | 150 m | |
|---|---|---|
| Device Type | Heat-shrink tubing | |
| Material | Polyolefin | |
| Cable Diameter (mm) | 0.8–1.6 mm | |
| Internal Diameter Before Shrinking (mm) | 1.6 mm | |
| Shrink Ratio | 2:1 | |
| Colour | Grey | |
| Adhesive Lined | No | |
| Manufacturer | Partex | |
| Model / SKU | ECHS216GREY | |
| Product type | Heat shrink tubing | |
| Product category | Heat shrink sleeving and cable insulation accessories | |
| Shrink ratio | 2:1 | |
| Nominal diameter before shrinking | 1.6 mm | |
| Nominal fully recovered diameter | 0.8 mm | |
| Colour | Grey | |
| Supplied length | 150 m | |
| Recovery method | Heat activated | |
| Form | Flexible tubular sleeving | |
| Application | Electrical insulation, wire identification and cable protection | |
| Suitable use | Small electrical wires, compatible cable joints and wiring assemblies | |
| HS Code | 39269097 |
The Partex ECHS216GREY is grey heat shrink tubing used for electrical wire insulation, cable identification, abrasion protection and covering compatible small wire joints or connections.
A 2:1 shrink ratio means the tubing can recover to approximately half its original internal diameter when heated correctly. For this product, the nominal diameter changes from 1.6 mm to 0.8 mm upon full recovery.
The tubing has a nominal supplied diameter of 1.6 mm and a nominal fully recovered diameter of 0.8 mm. It is intended for suitably sized small wires and electrical components.
The Partex ECHS216GREY is supplied in a 150 m pack, providing a substantial length of tubing for cutting into individual sleeves during electrical installation, manufacturing and maintenance work.
Cut the tubing to the required length, slide it over the wire or component, and apply controlled heat evenly using suitable hot-air equipment until the tubing contracts around the surface. Avoid overheating and follow appropriate electrical safety procedures.
Yes. The grey finish can be used as part of an organised cable identification system. However, conductor identification must comply with applicable wiring standards, and grey sleeving should not be assumed to indicate a particular conductor function without reference to the installation's identification scheme.
Partex supplies professional cable marking, identification and installation accessories for electrical and industrial applications. The ECHS216GREY grey 2:1 heat shrink tubing combines convenient heat-activated recovery, small-diameter wire coverage and a generous 150 m supply length to support efficient electrical insulation, cable identification and wiring protection.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.