Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
R281N/1 Partex Self Adhesive Cable Clips, 29 x 28mm – Bundle Dia. 12mm – 18mm, Natural, pack 100
Partex R281N/1 natural self-adhesive cable clips measure 29 x 28 mm and are designed to organise cable bundles with diameters from 12 mm to 18 mm on compatible mounting surfaces, supplied in a pack of 100.
£20.09
Why Choose the Partex R281N/1 Self Adhesive Cable Clips?
The Partex R281N/1 Self Adhesive Cable Clips provide a practical solution for securing and organising cables, wires and small cable bundles in electrical installations, control panels, equipment enclosures and general cable management applications. Designed for convenient surface mounting, these self-adhesive cable clips help maintain tidy cable routing without requiring drilled fixing holes in suitable installation conditions.
Each clip measures 29 mm × 28 mm and is designed to accommodate cable bundles with a diameter of approximately 12–18 mm. The natural colour provides a neutral appearance that suits a wide variety of electrical equipment and installation environments. The adhesive mounting arrangement allows the clips to be positioned on suitable clean, dry and smooth surfaces, helping installers organise cable runs and reduce loose wiring.
Supplied in a convenient pack of 100 clips, the Partex R281N/1 is suitable for electrical contractors, panel builders, maintenance engineers and equipment manufacturers requiring repeatable cable management solutions. Whether used for organising wiring inside electrical cabinets, routing cables around equipment or supporting cable bundles in suitable low-load applications, these clips provide a straightforward method of improving installation neatness and cable accessibility.
Key Advantages
- Self-adhesive mounting enables convenient installation on compatible surfaces.
- 29 mm × 28 mm dimensions provide a practical mounting footprint for cable management.
- Designed for cable bundles measuring 12–18 mm in diameter.
- Helps keep electrical wiring and cable bundles neatly organised.
- Can reduce the need for drilling or additional mechanical fixings in suitable applications.
- Natural colour offers a neutral appearance for electrical equipment and installations.
- Supports consistent cable routing inside control panels and equipment enclosures.
- Helps reduce loose or unsupported wiring where the adhesive mounting method is appropriate.
- Suitable for organising cables in electrical, electronic and industrial equipment.
- Allows installers to position cable supports along planned wiring routes.
- Practical for panel building, equipment assembly and maintenance work.
- Supplied in an economical pack of 100 clips for multiple installations.
Key Features
- Partex self-adhesive cable clip design.
- Manufacturer part number R281N/1.
- Clip dimensions: 29 mm × 28 mm.
- Compatible bundle diameter: 12–18 mm.
- Natural colour for discreet cable organisation.
- Adhesive-backed mounting arrangement for compatible surfaces.
- Designed to help retain and organise cable bundles.
- Suitable for use in appropriately prepared electrical equipment and enclosure surfaces.
- Convenient installation without drilling when adhesive fixing is suitable.
- Useful for maintaining orderly wiring layouts and cable routing.
- Suitable for professional electrical installation and equipment assembly.
- 100 cable clips per pack.
Practical Self-Adhesive Cable Management for Electrical Installations
Effective cable management is important for maintaining orderly electrical installations and making wiring easier to identify, inspect and maintain. The Partex R281N/1 Self Adhesive Cable Clips provide a convenient method of positioning and retaining cable bundles with diameters between 12 mm and 18 mm. Their 29 mm × 28 mm dimensions make them suitable for planned cable routing in compatible equipment enclosures, electrical cabinets and general wiring applications.
For reliable installation, the mounting surface should be clean, dry and free from dust, oil, grease and other contaminants that could interfere with adhesive bonding. The clip should be positioned carefully and pressed firmly onto a suitable surface in accordance with the adhesive manufacturer's application instructions. Adhesive performance depends on factors including surface material, surface preparation, temperature, cable weight and environmental conditions. The installation should be allowed to develop adequate adhesion before cables are loaded into the clip.
When planning a cable route, installers should consider cable bend radius, bundle diameter, accessibility and the number of clips needed to support the wiring appropriately. These self-adhesive clips are intended for cable organisation rather than as a substitute for specified mechanical cable supports or strain-relief devices. Where cable weight, vibration, heat, moisture or other installation conditions exceed the suitability of adhesive mounting, an appropriate mechanically fixed cable support should be used.
Typical Applications
- Electrical control panel cable management.
- Industrial automation cabinet wiring organisation.
- Switchgear and electrical distribution enclosure wiring.
- Electrical equipment and machinery cable routing.
- Electronic equipment assembly and internal wiring management.
- Organisation of cable bundles measuring 12–18 mm in diameter.
- Commercial electrical installation cable management.
- Maintenance and refurbishment of electrical equipment.
- OEM equipment manufacturing and panel building.
- Routing cables along compatible smooth mounting surfaces.
- General-purpose wiring organisation in suitable indoor environments.
- Neat positioning of low-load cable bundles where adhesive fixing is appropriate.
Technical Specifications
Tick the specs you need, then view products that match.
| Colour | Natural | |
|---|---|---|
| Length (mm) | 29 mm | |
| Width (mm) | 28 mm | |
| Device Type | Mount / Tool | |
| Manufacturer | Partex | |
| Manufacturer part number | R281N/1 | |
| Product type | Self-adhesive cable clip | |
| Mounting method | Self-adhesive | |
| Clip dimensions | 29 mm × 28 mm | |
| Minimum bundle diameter | 12 mm | |
| Maximum bundle diameter | 18 mm | |
| Bundle diameter range | 12–18 mm | |
| Colour | Natural | |
| Primary function | Cable and wire bundle organisation | |
| Typical mounting surfaces | Compatible clean, dry and smooth surfaces | |
| Typical applications | Cable management, electrical panels and equipment wiring | |
| Pack quantity | 100 clips | |
| HS Code | 39269097 |
Frequently Asked Questions
What are the Partex R281N/1 Self Adhesive Cable Clips used for?
The Partex R281N/1 cable clips are designed to secure and organise cables and wire bundles on compatible mounting surfaces. They are suitable for cable management in electrical panels, equipment enclosures, industrial machinery and general wiring installations where self-adhesive fixing is appropriate.
What size cable bundles can the R281N/1 clips accommodate?
The Partex R281N/1 clips are designed for cable bundles with diameters between 12 mm and 18 mm. The complete bundle diameter should be checked before installation to ensure it fits the clip correctly.
What are the dimensions and colour of the Partex R281N/1 clips?
Each Partex R281N/1 cable clip measures 29 mm × 28 mm and is supplied in a natural colour. These dimensions help installers plan clip positioning and available mounting space within electrical equipment.
How should the Partex R281N/1 self-adhesive cable clips be installed?
The clips should be applied to a compatible clean, dry and smooth surface free from dust, grease and other contaminants. Position each clip carefully and press it firmly into place according to the adhesive application instructions. Confirm adequate adhesion before loading the cable bundle, and use mechanical supports where adhesive fixing is unsuitable for the installation conditions.
How many Partex R281N/1 cable clips are supplied in a pack?
The Partex R281N/1 is supplied in a pack of 100 natural self-adhesive cable clips, making it a practical choice for electrical contractors, panel builders, equipment manufacturers and maintenance engineers managing multiple cable runs.
Trusted for Professional Cable Management
Partex self-adhesive cable clips offer a practical way to maintain neat and organised wiring in electrical installations and equipment assemblies. With a convenient adhesive mounting arrangement, a natural finish and compatibility with 12–18 mm cable bundles, the R281N/1 supports efficient cable routing and professional installation standards when correctly selected and applied.
