Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£292.95
The WAGO 753-667/000-104 is a high-performance 4-channel fail-safe digital input and 4-channel fail-safe digital output module designed for safety-related industrial automation applications. Part of the WAGO I/O System 750/753, it combines 24 V DC safety inputs, 2 A safety outputs, configurable safety logic and PROFIsafe communication in a compact DIN-rail-mounted module.
The module features four pulse-sensitive safety inputs and four safety-related power outputs, allowing safety sensors and actuators to be connected directly to compatible automation systems. Its integrated configurable safety logic enables safety-related applications up to SIL 3 and Performance Level e (PL e) without requiring a separate safety controller, provided the complete safety function is appropriately designed and validated.
Supporting PROFIsafe V2.6 over PROFINET, the WAGO 753-667/000-104 also provides 30 virtual inputs and 30 virtual outputs for exchanging information with a compatible controller. Configurable operating modes, input filtering, discrepancy monitoring and output diagnostics make it a flexible solution for machine safety, emergency stop systems, safety interlocks and industrial equipment protection.
The WAGO 753-667/000-104 combines safe digital inputs, safe power outputs and internal configurable logic in a single module. Four pulse-sensitive inputs can monitor safety devices such as emergency stop switches, guard interlocks, mode selectors and compatible electronic safety sensors. Two dedicated pulse outputs enable diagnostic testing of connected input circuits, supporting the detection of short circuits and cross-circuits.
The module provides four safety-related outputs rated at 2 A each, suitable for switching compatible resistive and inductive DC loads. The outputs support both bipolar and unipolar operation and include configurable test pulses, read-back monitoring and fault detection. Output wiring and connected loads must comply with the manufacturer's safety application requirements.
Integrated safety logic allows up to 12 configurable safety functions to be implemented within the module. This makes it possible to construct certain safety-related applications without a dedicated safety controller. The available 30 virtual inputs and 30 virtual outputs allow additional information to be exchanged with compatible controllers and incorporated into the configured logic.
For networked functional safety systems, the module supports PROFIsafe V2.6 over PROFINET. Its PROFIsafe address can be assigned using the module's DIP switch or suitable engineering software. Parameters are configured using WAGO Safety Editor, including operating modes, filtering, discrepancy monitoring and output test behaviour.
Depending on the selected architecture, the module can support safety functions up to Category 4 / PL e and SIL 3. The achievable safety rating depends on the complete safety circuit, including sensors, actuators, wiring, diagnostics, configuration and validation. The module's safety capability must not be treated as automatic certification of an entire machine safety function.
| System accessory | Yes |
|---|---|
| SIL according to IEC 61508 | 3 |
| Number of digital inputs | 4 |
| Supporting protocol for PROFIBUS | Yes |
| Type of output voltage | DC |
| Degree of protection (IP) | IP20 |
| Number of digital outputs | 4 |
| Supply voltage DC | 24 – 24 V |
| Suitable for rail mounting | Yes |
| Suitable for safety functions | Yes |
| Short-circuit protection, outputs available | Yes |
| Supporting protocol for PROFIsafe | Yes |
| Voltage type (supply voltage) | DC |
| Input current at signal 1 | 3 mA |
| Supporting protocol for PROFINET CBA | Yes |
| Supporting protocol for PROFINET IO | Yes |
| Type of electric connection | Spring clamp connection |
| Output current | 2 A |
| Explosion safety category for gas | ATEX gas-ex-protection, Cat. 3G |
| Explosion safety category for dust | ATEX dust-ex-protection, Cat. 3D |
| Height | 100 mm |
| Width | 24 mm |
| Performance level according to EN ISO 13849-1 | Level e |
| Permitted voltage at output | 24 – 24 V |
| Type of voltage (input voltage) | DC |
| Fieldbus connection over separate bus coupler possible | Yes |
| Depth | 67.8 mm |
| Manufacturer | WAGO |
| Series | WAGO I/O System 750/753 |
| Part number | 753-667/000-104 |
| Product type | Fail-safe digital input/output module with configurable safety logic |
| Communication protocol | PROFIsafe V2.6 over PROFINET |
| Number of pulse outputs | 2 |
| Nominal input voltage | 24 V DC |
| Input characteristic | Type 1 according to IEC 61131 |
| Input voltage for signal 0 | −3 to +5 V DC |
| Input voltage for signal 1 | 15–30 V DC |
| Typical input current at signal 1 | 3 mA per channel |
| Maximum input signal frequency | 50 Hz |
| Configurable input filter | 0–200 ms |
| Nominal output voltage | 24 V DC |
| Output current per channel | 2 A |
| Maximum total output current | 8 A |
| Output residual current at signal 0 | Less than 1 mA |
| Output switching | Configurable bipolar or unipolar operation |
| Pulse output current | 0.1 A per channel |
| Pulse output test duration | 0.5–200 ms, configurable |
| Digital output test pulse duration | 0–500 ms, configurable |
| Configurable output read-back time | 1–500 ms |
| Maximum capacitive load per output | 47 µF |
| Maximum permissible field cable length | 200 m |
| Safety logic functions | Up to 12 configurable functions |
| Virtual inputs | 30 |
| Virtual outputs | 30 |
| Achievable safety level | Up to SIL 3 / PL e, depending on the safety function and architecture |
| Relevant safety standards | IEC 61508, EN 62061 and EN ISO 13849-1 |
| Internal system supply | 5 V DC via data contacts |
| System supply current consumption | 120 mA |
| Field supply | 24 V DC SELV/PELV (−25% to +20%) |
| Field supply current consumption without external load | 30 mA |
| Electrical isolation | 500 V peak between system and field levels |
| Power jumper contact current capacity | 10 A |
| Incoming power jumper contacts | 2 |
| Outgoing power jumper contacts | 2 |
| Connection technology | 16 × CAGE CLAMP |
| Conductor cross-section | 0.08–2.5 mm² |
| Conductor size | AWG 28–14 |
| Conductor stripping length | 8–9 mm |
| Configuration software | WAGO Safety Editor (SEDI) and compatible engineering software |
| Operating temperature | 0 to +55 °C |
| Protection rating | IP20 |
| Mounting type | 35 mm DIN rail |
| Dimensions (W × H × D) | 24 × 100 × 67.8 mm |
| Housing colour | Yellow |
| Connector supply | 753 Series pluggable connectors and coding fingers ordered separately |
The WAGO 753-667/000-104 is a fail-safe digital input/output module used to monitor safety sensors and control safety-related actuators in industrial automation systems. It combines four safety inputs, four safety outputs and configurable safety logic.
The module provides four fail-safe digital inputs, four fail-safe digital outputs and two pulse outputs for diagnostic testing of connected safety sensor circuits.
Each safety-related digital output supports up to 2 A at 24 V DC, with a maximum combined output current of 8 A across the four output channels.
Yes. The module supports safety applications up to SIL 3 and PL e when used in an appropriate safety architecture. The achievable safety level depends on the complete safety function, including wiring, sensors, actuators, configuration and validation.
Yes. Its integrated configurable safety logic allows certain safety-related applications to operate without a separate safety controller. The module supports up to 12 configurable safety logic functions, subject to application requirements.
The module supports PROFIsafe V2.6 over PROFINET for safe communication with compatible automation systems. It can also operate independently of a safety controller using its integrated logic.
The module provides 30 virtual inputs and 30 virtual outputs for exchanging additional information with a compatible controller and incorporating that information into the module's configurable safety logic.
The module is configured using WAGO Safety Editor (SEDI) or compatible engineering software. Its PROFIsafe address can be set using the integrated DIP switch or software, while safety parameters such as input filtering, discrepancy times and output monitoring can be adjusted.
The module uses a 24 V DC SELV/PELV field supply with a permitted tolerance of −25% to +20%. It also receives its internal 5 V DC system supply through the WAGO I/O data contacts.
No. The 753 Series pluggable connectors and coding fingers are not included and must be ordered separately for the installation.
The WAGO 753-667/000-104 combines fail-safe digital I/O, integrated configurable safety logic and PROFIsafe communication in a modular industrial automation platform. Its four safety inputs, four 2 A safety outputs and extensive diagnostic capabilities provide flexible building blocks for appropriately engineered and validated machine safety applications.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.