Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£59.76
The WAGO 753-513 is a compact 2-channel relay output module designed for industrial automation, PLC control systems and distributed I/O applications. Part of the WAGO-I/O-SYSTEM 750/753, it provides two potential-free normally open (NO) relay contacts for switching compatible electrical loads at up to 250 V AC or 30 V DC, with a maximum switching current of 2 A per contact.
Unlike transistor-based digital output modules, the WAGO 753-513 uses electromechanical relay contacts to provide galvanically isolated switching. The relay coils are operated through the internal system supply, while the potential-free contacts allow external load circuits to be switched independently of the controller's logic supply. This makes the module suitable for industrial signalling, auxiliary control circuits, relay interfacing and equipment control.
Featuring two electrically isolated make contacts, 10 ms maximum pull-in and drop-out times, and green status LEDs for both channels, the WAGO 753-513 supports dependable switching and straightforward diagnostics. Its compact 12 mm-wide housing, DIN-rail mounting and removable WAGO 753 Series connector simplify installation, wiring and maintenance in industrial control cabinets.
The WAGO 753-513 provides a flexible interface between industrial automation controllers and external electrical circuits. Its two relay outputs operate as normally open, potential-free contacts, allowing the controller to switch external voltages without requiring the module to generate the load supply voltage. When a digital output is activated, the corresponding relay closes its contact and completes the connected circuit.
The module supports switching voltages up to 250 V AC or 30 V DC, with a maximum switching current of 2 A. This makes it suitable for compatible signalling equipment, auxiliary relays, control circuits and low-power electrical loads. The actual permissible load must also comply with the specified switching power, contact characteristics and electrical endurance limits.
Because the relay contacts are electrically isolated from one another, the two channels can be used to switch separate circuits, provided all applicable voltage, insulation and installation requirements are satisfied. The internal 5 V DC system supply energises the relays, while the external load circuits remain electrically separate from the controller's internal logic.
Each relay has a maximum pull-in and drop-out time of 10 ms, while integrated green LEDs provide immediate visual feedback of the relay states. The module is intended for normal relay switching rather than high-frequency pulse generation; its maximum switching frequency at nominal load is 0.5 Hz.
The WAGO 753-513 combines dependable electromechanical switching with modular DIN-rail construction and removable field wiring connections, supporting straightforward installation and maintenance in industrial control systems.
| System accessory | Yes |
|---|---|
| SIL according to IEC 61508 | None |
| Type of output voltage | AC |
| Degree of protection (IP) | IP20 |
| Number of digital outputs | 2 |
| Supply voltage DC | 24 – 24 V |
| Suitable for rail mounting | Yes |
| Type of digital output | Relay |
| Voltage type (supply voltage) | DC |
| Type of electric connection | Spring clamp connection |
| Output current | 2 A |
| Explosion safety category for gas | ATEX gas-ex-protection, Cat. 3G |
| Explosion safety category for dust | ATEX dust-ex-protection, Cat. 3D |
| Height | 100 mm |
| Width | 12 mm |
| Performance level according to EN ISO 13849-1 | None |
| Permitted voltage at output | 250 – 250 V |
| Fieldbus connection over separate bus coupler possible | Yes |
| Depth | 69.8 mm |
| Manufacturer | WAGO |
| Series | WAGO-I/O-SYSTEM 750/753 |
| Model | 753-513 |
| Product type | Digital relay output module |
| Total number of channels | 2 |
| Signal type | Digital |
| Output circuit design | 2 relay make contacts |
| Contact configuration | 2 × normally open (NO) |
| Output characteristic | Potential-free |
| Actuator connection | 2 × 1-wire |
| Maximum AC switching voltage | 250 V AC |
| Maximum DC switching voltage | 30 V DC |
| Minimum switching voltage | 5 V |
| Maximum switching current | 2 A |
| Minimum switching current | 10 mA |
| Maximum switching power | 500 VA / 60 W |
| Specified load characteristics | cos φ maximum 0.4; L/R maximum 7 ms |
| Maximum switching frequency | 0.5 Hz at nominal load |
| Maximum pull-in time | 10 ms |
| Maximum drop-out time | 10 ms |
| Typical contact bounce time | 1.2 ms |
| Minimum electrical endurance | 300,000 switching operations at maximum resistive load |
| Minimum mechanical endurance | 20 million switching operations |
| Maximum internal output data width | 2 bits |
| System supply voltage | 5 V DC via data contacts |
| System supply current consumption | 100 mA |
| Field-side power jumper function | Transmission of ground potential |
| Electrical isolation | 1,500 V between system and field levels |
| Incoming power jumper contacts | 1 |
| Outgoing power jumper contacts | 1 |
| Power jumper contact current-carrying capacity | 10 A |
| Status indicators | 2 green LEDs (A and C) |
| Connection technology | CAGE CLAMP® via pluggable connector |
| Field connection points | 8 |
| Solid conductor cross-section | 0.08–2.5 mm² |
| Fine-stranded conductor cross-section | 0.08–2.5 mm² |
| Conductor size | AWG 28–14 |
| Strip length | 9–10 mm |
| Operating temperature | 0 to +55 °C |
| Storage temperature | -25 to +85 °C |
| Protection rating | IP20 |
| Mounting type | DIN-35 rail |
| Module width | 12 mm |
| Module height | 69.8 mm |
| Module depth | 100 mm |
| Housing colour | Light grey |
| Compatible system | WAGO-I/O-SYSTEM 750/753 |
| Connector supply | Pluggable connector and coding fingers not included |
The WAGO 753-513 is a two-channel digital relay output module used to switch external AC or DC electrical circuits through potential-free normally open relay contacts.
The module provides two independent relay outputs, each featuring a normally open make contact.
The module supports a maximum switching voltage of 250 V AC or 30 V DC, subject to its current and switching power limits.
Each relay contact supports a maximum switching current of 2 A. The connected load must also remain within the module's voltage and switching power ratings.
A potential-free relay output provides an electrically isolated contact that opens or closes an external circuit without supplying its own load voltage.
The WAGO 753-513 provides two normally open (NO) make contacts. Each contact closes when its corresponding relay is energised.
Yes. The module can switch compatible 230 V AC loads, provided the current, switching power, load characteristics and installation conditions remain within the specified ratings.
Yes. The module supports DC switching up to 30 V DC, making it suitable for appropriately rated 24 V DC control circuits.
The maximum switching frequency is 0.5 Hz at nominal load. This module is intended for conventional relay switching rather than high-speed digital pulse applications.
The relays have maximum pull-in and drop-out times of 10 ms, with a typical contact bounce time of 1.2 ms.
Yes. The WAGO 753-513 provides electrically isolated normally open contacts, allowing separate external circuits to be switched within the module's insulation and operating limits.
Both modules provide two potential-free normally open relay outputs rated for up to 250 V AC and 2 A. The WAGO 753-513 uses a removable pluggable connector, whereas the WAGO 750-513 uses an integrated field wiring connection arrangement.
Yes. The module includes two green LEDs, labelled A and C, which indicate the operating states of relay outputs 1 and 2.
The relay module receives its internal operating supply through the 5 V DC system data contacts. The external load circuits require their own appropriately rated supply.
No. WAGO specifies that the 753 Series pluggable connector and coding fingers are not included and must be obtained separately.
The WAGO 753-513 is designed for operation at ambient temperatures from 0 to +55 °C.
The module is designed for DIN-35 rail mounting as part of a compatible WAGO-I/O-SYSTEM 750/753 station. Its 12 mm width supports space-efficient installation in industrial control cabinets.
WAGO relay output modules provide automation engineers, control panel builders and industrial system integrators with flexible interfaces for switching external electrical circuits. The WAGO 753-513 2-channel relay output module combines two potential-free normally open contacts, 250 V AC / 30 V DC switching capability, 2 A maximum contact current and convenient pluggable connectivity for industrial automation and control applications.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.