Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£66.65
The WAGO 753-513/000-001 is a compact 2-channel relay output module designed for industrial automation, PLC control systems and distributed I/O applications. Part of the WAGO-I/O-SYSTEM 750/753, this module provides two potential-free normally open (NO) relay contacts for switching compatible electrical loads at up to 250 V AC or 30 V DC, with a maximum switching current of 2 A.
The distinguishing feature of the /000-001 variant is its construction without power jumper contacts. Unlike the standard WAGO 753-513, this version does not pass field supply potentials through power jumper contacts to neighbouring I/O modules. This configuration is useful when designing modular I/O stations that require deliberate separation of field supply sections or where power jumper continuity is not required.
Featuring two electrically isolated make contacts, electromechanical relay switching and a removable WAGO 753 Series connector, the module provides a flexible interface between automation controllers and external control circuits. Integrated status LEDs assist with diagnostics, while the compact DIN-rail housing supports efficient installation in industrial control cabinets.
The WAGO 753-513/000-001 transfers digital control commands from a compatible automation controller to external electrical circuits using two electromechanical relays. Each relay operates a normally open contact that closes when its associated digital output is activated. Because the contacts are potential-free, the connected loads use their own external supply rather than receiving load voltage directly from the module.
The module supports switching voltages up to 250 V AC or 30 V DC, with a maximum contact current of 2 A. Its relay outputs can therefore be used for compatible auxiliary relays, signalling equipment, control circuits and other low-power electrical loads. The applicable switching power and load characteristics must also be considered when selecting connected devices.
A defining characteristic of the /000-001 version is the absence of power jumper contacts. In a modular WAGO I/O station, power jumper contacts normally distribute field supply potentials between adjacent modules. By omitting these contacts, the WAGO 753-513/000-001 provides an alternative configuration for applications where that field supply connection must not continue through the module. The overall I/O station must be designed so that any downstream modules receive the field supply connections they require.
The two relay contacts are electrically isolated, enabling separate external switching circuits within the manufacturer's specified ratings. Relay operation is controlled through the internal system supply, and the switching states are indicated by LEDs for convenient commissioning and troubleshooting.
With its removable connector interface and compact DIN-rail construction, the WAGO 753-513/000-001 provides a practical solution for industrial control systems requiring potential-free relay outputs and a module arrangement without power jumper contacts.
| System accessory | Yes |
|---|---|
| SIL according to IEC 61508 | None |
| Type of output voltage | AC |
| Degree of protection (IP) | IP20 |
| Number of digital outputs | 2 |
| Supply voltage DC | 24 – 24 V |
| Suitable for rail mounting | Yes |
| Type of digital output | Relay |
| Voltage type (supply voltage) | DC |
| Type of electric connection | Spring clamp connection |
| Output current | 2 A |
| Explosion safety category for gas | ATEX gas-ex-protection, Cat. 3G |
| Explosion safety category for dust | ATEX dust-ex-protection, Cat. 3D |
| Height | 100 mm |
| Width | 12 mm |
| Performance level according to EN ISO 13849-1 | None |
| Permitted voltage at output | 250 – 250 V |
| Fieldbus connection over separate bus coupler possible | Yes |
| Depth | 69.8 mm |
| Manufacturer | WAGO |
| Product number | 753-513/000-001 |
| Series | WAGO-I/O-SYSTEM 750/753 |
| Product type | Digital relay output module |
| Special variant | Without power jumper contacts |
| Total number of channels | 2 |
| Signal type | Digital |
| Output circuit design | Electromechanical relay |
| Contact configuration | 2 normally open make contacts |
| Output characteristic | Potential-free |
| Actuator connection | 2 × 1-conductor |
| Maximum AC switching voltage | 250 V AC |
| Maximum DC switching voltage | 30 V DC |
| Minimum switching voltage | 5 V |
| Maximum switching current | 2 A |
| Minimum switching current | 10 mA |
| Maximum switching power | 500 VA / 60 W |
| Maximum switching frequency | 0.5 Hz at nominal load |
| Maximum pull-in time | 10 ms |
| Maximum drop-out time | 10 ms |
| Internal output data width | 2 bits |
| System supply | Via internal system data contacts |
| Power jumper contacts | None |
| Relay contact isolation | Electrically isolated |
| Status indication | LED indication of relay switching states |
| Connection system | Removable WAGO 753 Series connector |
| Mounting type | DIN-35 rail |
| Compatible system | WAGO-I/O-SYSTEM 750/753 |
| Product status | Discontinued by manufacturer |
| Connector supply | Pluggable connector and coding fingers not included |
The WAGO 753-513/000-001 is a two-channel relay output module used to switch external AC or DC circuits through potential-free normally open contacts. It is specifically configured without power jumper contacts.
Both modules provide two potential-free normally open relay outputs rated for up to 250 V AC and 2 A. The key difference is that the 753-513/000-001 has no power jumper contacts, whereas the standard 753-513 includes power jumper contacts.
It means the module does not include the contacts normally used to pass field supply potentials between adjacent WAGO I/O modules. This allows the module to be used in station configurations where field supply distribution must be separated.
The module provides two independent relay output channels, each with a normally open make contact.
The module supports switching voltages up to 250 V AC or 30 V DC, subject to the specified contact current and switching power limits.
Each relay contact has a maximum switching current rating of 2 A.
The WAGO 753-513/000-001 provides two normally open (NO) contacts. Each contact closes when its associated relay is energised.
A potential-free output is an electrically isolated relay contact that switches an external circuit without supplying the load's operating voltage.
Yes. It can switch compatible 230 V AC circuits, provided the current, switching power, load characteristics and installation conditions remain within the module's specified ratings.
Yes. The module supports DC switching up to 30 V DC, making it suitable for appropriately rated 24 V DC control circuits.
Yes. The WAGO 753-513/000-001 provides electrically isolated normally open relay contacts for switching separate external circuits.
The specified maximum switching frequency is 0.5 Hz at nominal load. The module is intended for conventional relay switching rather than high-speed pulse applications.
No dedicated external 24 V DC field supply is required to energise the relay coils. The relays are operated using the module's internal system supply, while connected loads require their own appropriately rated external supply.
Yes. Integrated LEDs indicate the switching states of the relay outputs, helping with commissioning and troubleshooting.
WAGO currently identifies the 753-513/000-001 as discontinued. Availability should be checked with an authorised distributor, and any replacement should be assessed for electrical and mechanical compatibility.
No. The WAGO 753-513/000-001 is supplied without the pluggable connector and coding fingers, which must be obtained separately.
The module is designed for DIN-35 rail mounting as part of a compatible WAGO-I/O-SYSTEM 750/753 station. The field wiring is connected through a compatible removable WAGO 753 Series connector.
WAGO relay output modules provide automation engineers, control panel builders and industrial system integrators with flexible interfaces for switching external electrical circuits. The WAGO 753-513/000-001 combines two potential-free normally open relay contacts, 250 V AC / 30 V DC switching capability, 2 A maximum contact current and a configuration without power jumper contacts for specialised modular I/O installations.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.