Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£335.06
The WAGO 750-493/025-000 is a three-phase power measurement module with a 480 V AC voltage rating and 1 A current measurement inputs, designed for the modular WAGO-I/O-SYSTEM 750/753. This extended-temperature variant is intended for industrial electrical monitoring applications requiring measurement of three-phase voltage, current, active power and energy consumption.
With six measurement inputs comprising three voltage inputs and three current inputs, the module provides electrical measurement data for compatible WAGO controllers and fieldbus couplers. Its 16-bit resolution supports detailed monitoring of industrial electrical loads, while its compact 12 mm housing allows power measurement to be incorporated into distributed I/O stations without requiring a separate panel-mounted meter.
The /025-000 variant is specified for an extended ambient operating temperature range of −20 to +60 °C. It is particularly suitable for industrial control cabinets, machinery monitoring and energy management installations where operating conditions may exceed those of standard-temperature I/O modules.
The WAGO 750-493/025-000 is intended for AC power measurement using suitable current transformers. The current measurement inputs must not be connected directly to mains voltage, and the module must not be used for DC current measurement.
The WAGO 750-493/025-000 provides three-phase electrical measurement functionality within a modular industrial I/O system. It measures the electrical signals associated with three AC phases and makes the resulting process data available to the connected WAGO controller or fieldbus coupler.
The module can be used to monitor phase voltages, phase currents, active power, active energy and frequency. This information helps operators assess equipment loading, evaluate energy consumption and identify changes in electrical operating conditions.
The three current measurement inputs are rated for 1 A and must be connected through appropriately specified external current transformers. Transformer selection, secondary circuit protection and wiring must follow WAGO's installation instructions and the applicable electrical safety requirements. Direct connection of mains voltage to the current measurement inputs is prohibited.
The module provides 16-bit measurement resolution and supports frequency analysis within its specified input limits. Additional power quantities, such as reactive power and apparent power, may be calculated in a compatible controller using appropriate function blocks rather than being provided as independent native measurements by this module.
The extended-temperature construction allows the 750-493/025-000 to operate from −20 to +60 °C. This makes it useful for industrial control cabinets and distributed I/O installations exposed to wider temperature variations, provided the complete system is designed for those environmental conditions.
Important installation requirement: This module is intended for AC measurement. WAGO has issued safety guidance restricting DC current measurement applications involving the 750-493 family. Installation, commissioning and maintenance should be performed by suitably qualified electrical personnel using the current manufacturer documentation.
| System accessory | Yes |
|---|---|
| Supporting protocol for other bus systems | Yes |
| SIL according to IEC 61508 | None |
| Supply voltage AC 50 Hz | 277 – 277 V |
| Degree of protection (IP) | IP20 |
| Power consumption | 1 W |
| Number of analogue inputs | 6 |
| Supply voltage AC 60 Hz | 277 – 277 V |
| Resolution of the analogue inputs | 16 bit |
| Supply voltage DC | 5 – 5 V |
| Suitable for rail mounting | Yes |
| Input, current | Yes |
| Voltage type (supply voltage) | DC |
| Input, voltage | Yes |
| Explosion safety category for gas | ATEX gas-ex-protection, Cat. 3G |
| Explosion safety category for dust | ATEX dust-ex-protection, Cat. 3D |
| Height | 100 mm |
| Performance level according to EN ISO 13849-1 | None |
| Width | 12 mm |
| Fieldbus connection over separate bus coupler possible | Yes |
| Depth | 67.8 mm |
| Brand | WAGO |
| Manufacturer part number | 750-493/025-000 |
| Product designation | 3-Phase Power Measurement; 480 VAC, 1 A; Ext. Temperature |
| Product series | WAGO-I/O-SYSTEM 750/753 |
| Product category | Three-phase power measurement I/O module |
| Product variant | Extended temperature |
| Number of measurement inputs | 6 |
| Voltage measurement inputs | 3 |
| Current measurement inputs | 3 |
| Rated phase-to-phase measurement voltage | 480 V AC |
| Rated phase-to-neutral measurement voltage | 277 V AC |
| Maximum measurement current | 1 A |
| Current measurement connection | External current transformers with suitable 1 A secondary ratings |
| Measurement resolution | 16 bits |
| Typical voltage input resistance | 1,072 kΩ |
| Typical current input resistance | 22 mΩ |
| Frequency range, DC filter enabled | 10–2,000 Hz |
| Frequency range, DC filter disabled | 0–2,000 Hz |
| Maximum signal frequency | 7.2 kHz |
| Nominal mains frequency range | 45–65 Hz |
| Measurement error at reference temperature | Maximum 0.5% of upper-range value |
| Measurement reference temperature | 25 °C |
| Internal system supply voltage | 5 V DC via internal data bus |
| Internal current consumption | 100 mA |
| Overvoltage category | III |
| Rated impulse voltage | 4 kV |
| Pollution degree | 2 |
| Operating temperature | −20 to +60 °C |
| Connection technology | CAGE CLAMP® |
| Conductor cross-section | 0.08–2.5 mm² |
| Conductor size | 28–14 AWG |
| Conductor strip length | 8–9 mm |
| Module width | 12 mm |
| Module height | 100 mm |
| Depth from upper edge of DIN rail | 64 mm |
| Mounting type | DIN-35 rail |
| Housing colour | Light grey |
The WAGO 750-493/025-000 is a three-phase power measurement module for the WAGO-I/O-SYSTEM 750/753, rated for 480 V AC phase-to-phase voltage measurement and 1 A current transformer inputs, with an extended operating temperature range.
The module measures electrical parameters in compatible three-phase AC installations, allowing industrial controllers to monitor voltage, current, active power, energy consumption and frequency.
The /025-000 suffix identifies the extended-temperature, 1 A variant, which operates from −20 to +60 °C.
The module is rated for 480 V AC phase-to-phase and 277 V AC phase-to-neutral measurement.
Each current measurement input is designed for a maximum rated measurement current of 1 A, normally supplied by a suitable external current transformer.
The module has six measurement inputs: three voltage measurement inputs and three current measurement inputs.
Yes. Suitable external current transformers must be used for current measurement. The current measurement inputs must never be connected directly to mains voltage.
No. WAGO has issued safety guidance prohibiting DC current measurement applications for this module family. The 750-493/025-000 should be used only within its specified AC measurement application.
The module supports three-phase voltage and current measurement, active power and active energy monitoring, phase position information and frequency measurement. Other calculated power quantities may require controller function blocks.
The WAGO 750-493/025-000 provides 16-bit measurement resolution.
The extended-temperature variant operates at ambient temperatures from −20 to +60 °C.
Both are three-phase power measurement modules with 480 V AC voltage measurement and 1 A current inputs. The 750-493/025-000 is the extended-temperature variant, specified for operation from −20 to +60 °C.
The 750-493/025-000 has 1 A current measurement inputs, while the 750-493/025-001 is the corresponding extended-temperature version with 5 A current measurement inputs.
The module receives its internal 5 V DC system supply through the WAGO I/O station's internal data bus and has a specified internal current consumption of 100 mA.
Yes. It is designed for installation in a compatible WAGO 750/753 I/O station mounted on a standard 35 mm DIN rail.
No. It is a three-phase power measurement I/O module that operates within a compatible WAGO-I/O-SYSTEM 750/753 station. It provides measurement data to the connected controller or fieldbus system.
Reactive and apparent power values can be calculated using suitable function blocks in a compatible controller. They should not be assumed to be independent native measurements of the 750-493/025-000.
Yes. When installed with suitable current transformers and compatible WAGO automation equipment, the module can provide electrical measurement data for machinery load monitoring, energy consumption analysis and industrial process supervision.
WAGO three-phase power measurement modules support integrated electrical monitoring for automation engineers, control panel builders, industrial maintenance teams and energy management specialists. The WAGO 750-493/025-000 combines 480 V AC three-phase voltage measurement, 1 A current transformer inputs, 16-bit resolution and extended-temperature operation to support industrial power and energy monitoring within compatible WAGO 750/753 I/O systems.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.