Standard delivery
£8 ex VAT · free over £200UK parcel delivery is £8 ex VAT, or free on orders over £200 ex VAT.
Heavier items may be charged at a weight-based or pallet rate, shown at checkout.
£53.92
The WAGO 706-7753/304-200 is a preassembled 2 m system cable designed for the WAGO-I/O-SYSTEM 750 Series. Featuring a 20-pole female connector at one end and two 14-pole female connectors at the other, this cable provides a convenient connection between compatible WAGO I/O modules and interface adapters.
Designed for a 2 × 8 analog input or output configuration, the WAGO 706-7753/304-200 enables organised signal wiring within industrial automation systems. Its factory-assembled connectors eliminate the need for manual ribbon connector termination, helping reduce installation time and improve wiring consistency.
The cable uses 0.14 mm² LiYY conductors with colour coding according to DIN VDE 47100. With an operating voltage of up to 35 V AC/DC, a maximum current of 1 A per conductor and an IP20 protection rating, it is suitable for compatible low-voltage industrial control and signal wiring applications.
The WAGO 706-7753/304-200 system cable provides a structured connection between compatible WAGO I/O modules and industrial interface adapters. Its 20-pole female DIN 41651 connector connects to the designated system wiring interface, while the two 14-pole female DIN 41651 connectors provide separate connections for compatible interface equipment.
The cable can be used in suitable system wiring arrangements incorporating WAGO JUMPFLEX® interface adapters 857-981 and 857-982. WAGO also identifies the related 750-1500 and 750-1502 digital I/O modules in its interface cable compatibility documentation. Although the product is classified as supporting a 2 × 8 analog I/O configuration, the actual signal functionality depends on the connected I/O modules and adapters. The relevant pin assignment and module compatibility documentation should therefore be checked before installation.
Its 2 m cable length provides convenient routing between equipment installed within industrial control cabinets. The preassembled connector arrangement helps reduce the number of individual signal terminations, improving installation consistency and making cable replacement more straightforward.
The WAGO 706-7753/304-200 is a passive system cable. It does not independently process, convert or isolate signals. Electrical ratings must be observed, including the manufacturer's reduced current limit of 0.7 A per conductor when more than 10 conductors are used simultaneously.
| Suitable for input board PLC | Yes |
|---|---|
| Type of electrical connection, field-sided | Other |
| Type of electrical connection, box-sided | Other |
| Suitable for output card PLC | Yes |
| Function | PLC - other devices |
| Suitable for digital signals | Yes |
| Suitable for analogue signals | Yes |
| Number of poles | 20 |
| Length | 2 m |
| Manufacturer | WAGO |
| Series | 706 Series |
| Model | 706-7753/304-200 |
| Product type | Preassembled system cable |
| Application | Industrial I/O system wiring |
| Compatible I/O system | WAGO-I/O-SYSTEM 750 Series |
| Input/output configuration | 2 × 8 analog inputs or outputs |
| Cable length | 2 m |
| Cable type | LiYY |
| Conductor cross-section | 0.14 mm² |
| Conductor colour coding | DIN VDE 47100 |
| Connection 1 connector | Female DIN 41651 |
| Connection 1 number of poles | 20 |
| Connection 2 connector | Female DIN 41651 |
| Connection 2 number of poles | 14 |
| Connection 3 connector | Female DIN 41651 |
| Connection 3 number of poles | 14 |
| Operating voltage | ≤35 V AC/DC |
| Maximum current per conductor | 1 A |
| Maximum current per conductor with more than 10 conductors in use | 0.7 A |
| Protection rating | IP20 |
| Operating temperature | −25 to +70 °C |
| Cable shielding | Unshielded |
| Connector termination | Insulation displacement connection (IDC) |
| Compatible interface adapters | WAGO 857-981 and 857-982, subject to the connected I/O module configuration |
| GTIN/EAN | 4050821034186 |
| Weight | Approx. 181 g |
The WAGO 706-7753/304-200 is a preassembled system cable designed for connecting compatible WAGO-I/O-SYSTEM 750 Series equipment to suitable interface adapters and system wiring components.
The cable is designed for the WAGO-I/O-SYSTEM 750 Series. Compatibility with individual I/O modules and interface adapters should be checked against the relevant WAGO documentation.
The WAGO 706-7753/304-200 has a cable length of 2 m, making it suitable for connections between compatible I/O modules and interface equipment within industrial control cabinets.
The cable has one 20-pole female DIN 41651 connector at one end and two 14-pole female DIN 41651 connectors at the other end.
WAGO specifies the cable for a 2 × 8 analog input or output configuration. The actual number and type of signals available depend on the connected modules and their pin assignments.
The cable uses 0.14 mm² LiYY conductors with conductor colour coding according to DIN VDE 47100.
The cable is specified for an operating voltage of up to 35 V AC/DC. The connected I/O modules and interface adapters must also be rated for the intended electrical conditions.
The maximum current is 1 A per conductor. When more than 10 conductors are used simultaneously, the manufacturer's specified maximum current is reduced to 0.7 A per conductor.
Yes. The cable is suitable for compatible system wiring arrangements incorporating WAGO JUMPFLEX® interface adapters 857-981 and 857-982. The precise I/O module and connector assignments must be verified before installation.
No. The WAGO 706-7753/304-200 is a passive cable assembly. It provides electrical connections between compatible devices but does not independently convert, amplify, isolate or process signals.
The cable is specified for an operating temperature range of −25 to +70 °C.
The cable assembly has an IP20 protection rating and should be installed inside an appropriately protected electrical enclosure.
No. The WAGO 706-7753/304-200 is an unshielded cable assembly. Its suitability for a particular signal application depends on the installation environment and electromagnetic compatibility requirements.
These cables use the same 20-pole to dual 14-pole connector arrangement but have different lengths. The 706-7753/304-100 is 1 m long, the 706-7753/304-200 is 2 m long and the 706-7753/304-300 is 3 m long.
No. Compatibility depends on the module's system connector, pin assignment, channel configuration and electrical characteristics. The cable should only be used with compatible WAGO I/O modules and interface adapters.
WAGO 706 Series system cables provide practical connectivity solutions for industrial automation engineers, electrical panel builders and machine manufacturers. The WAGO 706-7753/304-200 combines a preassembled 2 m cable, a 20-pole to dual 14-pole DIN 41651 connector arrangement and compatibility with designated WAGO I/O system wiring equipment to simplify industrial signal connections and support efficient control cabinet installations.
We use cookies
We use essential cookies to run this site, your basket and checkout. With your permission we'd also like to use analytics and advertising cookies to understand how the site is used and to measure our adverts.